Omnia producta

Siemens 6ES7131-1BL12-0XB0 SIMATIC ET 200L 200SC 32DI Electronic Block

Siemens 6ES7131-1BL12-0XB0 SIMATIC ET 200L 200SC 32DI Electronic Block

Nomen producti: SIMATIC ET 200L 200SC 32DI Electronic Block

Nomen Marcae: Siemens

Numerus Modeli: 6ES7131-1BL12-0XB0

Locus Originis: Germania

Garantia: 12 Mensis

Whatsapp: +86 18020776782

Inscriptio electronica: [email protected]

Appurtenance:

Conspectus
DESCRIPTIO
I/O Setup
Diagnosis
Specificationes
Commercial Term
INFORMATIO CONTACTUS
Quaestiones Frequentes
Other Products
Producta commendata

Thirty-two-channel digital input block for legacy distributed PROFIBUS I/O stations

The Siemens ET 200L 200SC electronic block provides 32 digital inputs for 24 V DC signals and supports expansion with up to 16 additional SIMATIC SC channels when the installed terminal and station configuration permit it.

I/O replacement check: Confirm the TB32L terminal block, ET 200L station type, PROFIBUS address and rate, 2-wire sensor wiring, channel map, expansion modules and archived hardware configuration before ordering.

DESCRIPTIO

6ES7131-1BL12-0XB0 est un bloc électronique SIMATIC DP hérité pour les stations ET 200L 200SC. Ses 32 entrées sont configurées pour des signaux de terrain à 24 V CC, et la fiche technique officielle indique la possibilité d’extension avec des modules numériques et analogiques SIMATIC SC.

Un remplacement contrôlé dépend de la base de bornes et de la carte d’E/S du projet. Prendre une photo du câblage sur site, enregistrer chaque canal et chaque alimentation de capteur, sauvegarder la configuration matérielle PROFIBUS et examiner les diagnostics de la station avant le retrait.

I/O Setup

La base de bornes et la carte des canaux doivent être considérées comme faisant partie intégrante du remplacement, et non comme des accessoires interchangeables.

Basis Terminalis

Vérifier l’état, le système de clavage, la pression de contact et la compatibilité de TB32L avant d’insérer le bloc électronique de remplacement.

CHANNEL MAP

Enregistrer toutes les 32 affectations de signaux, les références communes et les alimentations de capteurs à deux fils issues du projet et du câblage sur site.

Extension SC

Identifier chaque module SIMATIC SC connecté et confirmer les canaux d’extension configurés avant la mise en service.

Diagnosis

Use station diagnostics and a channel-by-channel input test to separate field wiring faults from block faults.

Bus status

Confirm station address, PROFIBUS rate, connector termination and diagnostic status before replacing the block.

Signal test

Measure the affected 24 V DC input at the terminal and compare the LED and PLC process image.

Test d’acceptation

Test every required input and expansion channel against the approved I/O checklist before production release.

Specificationes

Designatio generis producti	ET 200L 200SC electronic block 32DI
Numerus ordinis	6ES7131-1BL12-0XB0
Usable terminal block	TB32L
Tensio nominalis supplicii	24 V DC
Ingressus Digitales	32
Input signal 0	−30 ad +5 V DC
Signum introductum 1	13 to 30 V DC
Morae Ingressus	2 ad 4,5 ms
Longitudo Cavi Scutati	Usque ad 1000 m
Longitudo cavi non scutati	Usque ad 600 m
Velocitas PROFIBUS DP	Usque ad 1,5 Mbit/s
Ammissio Potentiae	Typice 4.8 W

Commercial Term

Praeoffertio

Pretium praesens et disponibilitas

Solutio

T/T aut condicionibus conventis

Tempus praecedens

Confirmatum cum citatione

Navigatio

DHL, FedEx, UPS aut oneribus conventis

Garantia

12 Mensis

INFORMATIO CONTACTUS

Contactus

Iimus Pei

[email protected]

+86 180 2077 6782

Quaestiones Frequentes

Num 6ES7131-1BL12-0XB0 in quodlibet terminale ET 200L inseri potest?

Non. Hoc electronicum blocum 32-introductorium ad terminale TB32L specificatur. Antequam emas, inspice notam, clavem et statum contactuum TB32L; aliud basis simile videri potest, sed non praebet ordinem terminalium 32-channelis requisitum.

Cur 6ES7131-1BL12-0XB0 sensorem qui circa 9 V in introducto metitur non agnoscit?

Novem volti inter limites logicos specificatos iacent: signum 0 est usque ad 5 V, signum 1 autem ab 13 V incipit. Introductum contra suum rectum referentiam sub onere mete, deinde corrigere suppetias sensoris, reditum commune vel viam percolationis, non autem modulum ut defectivum tractare.

Quid saepe causat ut plures introductus adiacentes in 6ES7131-1BL12-0XB0 simul micent?

A group symptom points first to the shared 24 V sensor supply, reference conductor, TB32L contact or connector seating. Trend the supply at the terminal while the load changes and compare the input LEDs with the PLC process image to separate field power loss from bus or module faults.

Why does the ET 200L station report a configuration fault after 6ES7131-1BL12-0XB0 is replaced?

The configured module sequence must match the physical station, including every SIMATIC SC expansion module. Confirm the 32DI block position, the expansion order and channel count, then compare the station diagnostics with the saved hardware configuration before editing the PLC project.

Can 6ES7131-1BL12-0XB0 operate on a PROFIBUS DP segment configured above 1.5 Mbit/s?

No. The published maximum PROFIBUS DP rate for this electronic block is 1.5 Mbit/s. If the installed segment runs faster, do not solve the mismatch by changing only the station address; the network rate or the hardware architecture must be redesigned.

How can I commission 6ES7131-1BL12-0XB0 without missing a crossed field wire?

Use an approved channel checklist and stimulate one field signal at a time. For each of the 32 inputs, compare the terminal voltage, module LED, configured channel address and PLC process image, then repeat the same test for any attached SIMATIC SC expansion channels.

Other Products

C1B	XY2CE2A296	220614
R0F1314228/5 TVM113-013	X13760335-01 Rev.R TD7	EXP-1048
METSEPM5560	HWS600-24/LNT	181737 RL28-55-LAS-2840/47/115b
DDI 24-12 018	SNB-5003P	3122A 5000V
ABB MU6301/90-811-500 2CKA006300A1405	15B10730G1 EDP70	IR-720-EUR
A51 6762250 AE4 6762264 AE02	FTD110DBMicro-SST	PG1-M10 674-686MHz PG185
DN15 TSMR-015-A5T-MB	45196504	ADAM-5000/TCP
7-061-0006 V5L26985	EST 140331	MN-S4-500-A
C2IR-8 6500429	TPNN0077	ABB MT70 GHQ6050059R0006
WCU 8100261	4269-593	ST-IO ZA10341