Omnia producta

Siemens 6SE7090-0XX85-1DA0 SIMOVERT MASTERDRIVES CUR Module

Siemens 6SE7090-0XX85-1DA0 SIMOVERT MASTERDRIVES CUR Module

Nomen producti: SIMOVERT MASTERDRIVES CUR Control Module

Nomen Marcae: Siemens

Numerus Modeli: 6SE7090-0XX85-1DA0

Locus Originis: Austria

Garantia: 12 Mensis

Whatsapp: +86 18020776782

Inscriptio electronica: [email protected]

Conspectus
Legacy Drive Matching
DESCRIPTIO
Specificationes
Service diagnostics
Commercial Term
INFORMATIO CONTACTUS
Quaestiones Frequentes
Other Products
Producta commendata

Legacy CUR control module for SIMOVERT MASTERDRIVES infeed and regenerative feedback units

Exact spare and software check: Match the complete CUR order number, installed power unit, board and connector revision, software or EPROM identity and parameter archive. Do not energize an unmatched board or assume that a SINAMICS migration is a board-only replacement.

This replacement control module is specified for SIMOVERT MASTERDRIVES infeed and infeed/regenerative feedback units. Siemens identifies associated software 6SW1701-0DA14 for T434E support and lists the product as a cancelled spare with migration toward LV SINAMICS.

Legacy Drive Matching

Board identity, host power unit and software must be matched as one service package before the CUR module is installed.

Host unit identity

Record the complete infeed or regenerative unit order number, rating, cabinet function and machine reference.

Editio Tabulae

Photograph the CUR label, connector orientation, EPROM or software labels and all installed option boards.

Software scope

Confirm the required 6SW1701-0DA14 software support and retain the approved parameter and commissioning archive.

DESCRIPTIO

6SE7090-0XX85-1DA0 is a CUR control-module spare for legacy SIMOVERT MASTERDRIVES line-side units. The official product record specifically associates software 6SW1701-0DA14 with T434E support.

Because the module is cancelled and application-sensitive, procurement should be based on the original unit nameplate, board labels, installed software and the complete infeed or regenerative unit order number. Preserve the drive parameter and fault history before removal.

Specificationes

Designatio generis producti	SIMOVERT MASTERDRIVES CUR Control Module
Numerus ordinis	6SE7090-0XX85-1DA0
Applicatio	Infeed and infeed/regenerative feedback units
Software adiunctum	6SW1701-0DA14
Software support reference	T434E
Status cyclī vītae	Product cancelled since 6 October 2011
Migration reference	Migration toward LV SINAMICS
Service status	Spare part with repair or replacement service options
Ponderis netum	0.400 kg
Dimensiones Confectionis	26 x 33 x 9,5 cm
Patria Origin	Austria
Commodity / class	85049090; Siemens product class D

Service diagnostics

Capture evidence while the legacy drive can still communicate; a board exchange should follow safe isolation and controlled checks.

Fault record

Save active and historical faults, parameter values, ready-state information and the sequence that causes the trip.

Tuta Isolatio

Follow the drive discharge and lockout procedure, prove the DC link is safe and label each connector before handling the board.

Reinitiatio controlata

Check seating, connectors and software identity before power-up, then verify the host unit state before enabling regeneration.

Commercial Term

Praeoffertio

Pretium praesens et disponibilitas

Solutio

T/T aut condicionibus conventis

Tempus praecedens

Confirmatum cum citatione

Navigatio

DHL, FedEx, UPS aut oneribus conventis

Garantia

12 Mensis

INFORMATIO CONTACTUS

Tempus

Contactus

Iimus Pei

[email protected]

+86 180 2077 6782

Quaestiones Frequentes

How can I confirm that 6SE7090-0XX85-1DA0 is the correct CUR spare for my MASTERDRIVES unit?

Match the full CUR order number, host infeed or regenerative unit order number, board and connector revision, EPROM or software label and cabinet wiring. Provide clear photos and the original unit nameplate before ordering.

Cur est software 6SW1701-0DA14 importante dum 6SE7090-0XX85-1DA0 substituitur?

Siemens identificat 6SW1701-0DA14 ut software associatum pro subsidio T434E. Confirmare debes ut software, set parameterum et revisio tabulae ad applicationem installatam pertinent antequam reservatum instrumentum in operationem ducatur.

Quid servare debes antequam 6SE7090-0XX85-1DA0 removetur?

Serva archivum parametrorum et commissionis, defectus activos et historicos, numerum ordinis unitatis principalis, titulos tabularum, identitatem software vel EPROM et photographemas connectorum. Serva originale modulum usque dum substitutum functionales experimenta superaverit.

Cur unitas principalis manere potest non parata postquam 6SE7090-0XX85-1DA0 installatur?

Cum impulsum securiter isolaveris, iterum inspice positionem tabulae, omnem connexorem clavem habentem, compatibilitatem software vel EPROM et restitutum set parametrorum. Ad initiationem potentiae, notare primam faultam et statum unitatis principalis antequam reset repetas aut hardware mutes.

Quae informationes praebere debes pro diagnosi vel citatione 6SE7090-0XX85-1DA0?

Provide the complete host-unit and CUR order numbers, rating plate, board revision, software labels, parameter backup status, active faults, cabinet function and clear photos of both sides and all connectors.

Can 6SE7090-0XX85-1DA0 be replaced directly by a SINAMICS component?

No board-level drop-in migration should be assumed. Siemens points to LV SINAMICS migration, which requires an engineered review of the power section, regenerative function, motor and line data, control interfaces, safety, cabinet mechanics and commissioning software.

Other Products

QBE63-DP01	MMC-120A-F000	KP551
7000005-679	UG-3-A4O	ABB 500MDD01 1KGT034200R001
POL945.00/MCQ	225629-007	45123-3
2791.00	80025-523-10	RL28-55-LAS-2840/47/115b
TT5000	GX1230	RS485
IC00P02DAL	FTS35-4011-22M	45123-9
MIC-1000	GE IC200ALG431F GE IC200CHS002D	DPI 705
AT-IR-CS-TX	LFC7510	19A3716X022
Sal31.00T10	571125022 I4DVW-0000	FW-325
ABB PM554-TA1 1TNE968900R0100	MSR2	PCX924