Omnia producta

Siemens SIMATIC S7-1500 6ES7532-5NB00-0AB0 AQ 2xU/I ST Analog Output Module

Siemens SIMATIC S7-1500 6ES7532-5NB00-0AB0 AQ 2xU/I ST Analog Output Module

SIEMENS | SIMATIC S7-1500

6ES7532-5NB00-0AB0

Modulus output analogi AQ 2xU/I ST cum duobus canalibus tensionis/currentis, resolutione 16-bit, accurate operationis 0.3% et diagnosticis canalium.

Tempus ducens: In stoce

Garantia: unum annum

Inquisitio per epistulam electronicam [email protected]

WhatsApp +86 18159889985

Appurtenance:

Conspectus
Data Technica
Inquisitio
Proprietates
Interfacies
Installatio
Environment
Quaestiones Frequentes
Modellos Recommandatos
Producta commendata

Siemens SIMATIC S7-1500 AQ 2xU/I ST

Exact configured model: 6ES7532-5NB00-0AB0

OFFICIAL PRODUCT IDENTITY

Standard analog output module with two channels in one group, voltage and current output ranges, diagnostics, substitute values and 16-bit resolution. The delivery includes a 40-pole push-in front connector, infeed element, shielding bracket and shield terminal.

Configured geometry

25 mm width, 147 mm height and 129 mm depth; approximate weight 200 g.

Connection package

Two analog output channels support voltage and current loads. Supported ranges include 0 to 10 V, 1 to 5 V, -10 to +10 V, 0 to 20 mA, -20 to +20 mA and 4 to 20 mA.

Installation focus

Install in the S7-1500 rack, connect 24 V DC load voltage, use the supplied push-in front connector, route shielded analog cables through the shielding hardware and parameterize each channel before commissioning.

Examinatio Emptionis

Match every segment of 6ES7532-5NB00-0AB0. Confirm AQ 2xU/I ST, two channels, 16-bit resolution, included 40-pole push-in connector, voltage/current ranges and exact suffix 5NB00-0AB0.

Data Technica

Configuratio et specificatio officialis

Modello completo	6ES7532-5NB00-0AB0
Familia producti	Siemens SIMATIC S7-1500
Typus Producti	AQ 2xU/I ST analog output module
Official Description	Modulus output analogus duo canalium pro voltatione et currente, resolutio 16-bit, exactitudo operationis 0.3%, diagnostica et valores substituti
Hardware / firmware	FS01 / V1.0.0
Tensio nominalis supplicii	24 V DC; permisum est 19.2 usque ad 28.8 V DC
Consumptio currentis	maxime 110 mA
Ammissio Potentiae	2.7 W typice
Numerus emissionum analogicarum	2
Intervalla Voltaminis	0 ad 10 V; 1 ad 5 V; -10 ad +10 V
Intervalla Curris	0 ad 20 mA; -20 ad +20 mA; 4 ad 20 mA
Exolvuntur tempore	minime 3.2 ms pro omne canales
Resolutio	16 bit cum signo, cum superintervallo
Conversio Tempus	0.5 millisecondum per canalum
Accuratio Operationis	±0.3% pro voltatione et currente per totum intervallum temperaturarum
Voltage load	Minimum 1 kΩ; 0.5 kΩ pro 1 ad 5 V
Onus Electricum	Maximum 750 Ω
Longitudo Cavi Scutati	Usque ad 800 m pro currente; 200 m pro voltatione
Diagnosis	Tensio alimentaria, interruptio fili pro currente, circuitus brevis pro voltatione, excessus/defectus
Conector Anterior	conector anterior 40-polus ad inserendum praebitus
Dimensiones	25 x 147 x 129 mm (latus x altus x profundus)
Pondus	Circiter 200 g
Temperatura operativa	Horizontaliter: -30 ad +60 °C ab FS04; verticaliter: -30 ad +40 °C ab FS04
Altitudo Installationis	Usque ad 5 000 m; restrictiones supra 2 000 m
Official Document	Siemens data sheet 6ES7532-5NB00-0AB0, pages 1–3; last modified 2023-08-16

Inquisitio

Contactus

Stella

Inquisitio per epistulam electronicam [email protected]

WhatsApp +86 18159889985

Proprietates

Flexible analog outputs

Each of the two channels can be parameterized for supported voltage or current ranges with substitute values and diagnostics.

Conversio Praecisa

The module provides 16-bit resolution, 0.5 ms conversion per channel and ±0.3% operational accuracy over the full temperature range.

Safety-Related Tripping

From the specified hardware status, standard-module load groups can be shut down for applications up to PL d, Category 3 and SIL 2.

Interfacies

Voltage output modes

Supported voltage ranges are 0 to 10 V, 1 to 5 V and −10 to +10 V with two-wire or four-wire actuator connection.

Current output modes

Supported current ranges are 0 to 20 mA, −20 to +20 mA and 4 to 20 mA with two-wire actuator connection.

Connector and shielding

The supplied 40-pole push-in front connector, infeed element, shielding bracket and shield terminal form the field-wiring interface.

Installatio

Rack and load voltage

Mount the 25 mm wide module in the S7-1500 rack and supply 24 V DC within the official 19.2 to 28.8 V range.

Conectio canalium

Select the correct voltage or current terminal assignment, observe load impedance and cable-length limits, and connect the cable shield to the supplied shielding hardware.

Parameterization and test

Configure each channel range and substitute value, then verify diagnostics, signal direction and measured output before connecting the final actuator.

Environment

Orientation limits

Horizontal installation is specified up to +60 °C; vertical installation is specified up to +40 °C. Minimum -30 °C values apply from the stated hardware status.

Altitudo

Operation is specified up to 5,000 m, with restrictions for installation altitudes above 2,000 m.

Monitorium Diagnosticum

RUN, ERROR, PWR, channel-status and channel-diagnostic LEDs support commissioning and maintenance inside the control enclosure.

Quaestiones Frequentes

Q1. Quomodo exactum 6ES7532-5NB00-0AB0 in citatione offertum verificare possum?

Examina integrum numerum ordinis, designationem AQ 2xU/I ST, duo analogica output, resolutionem 16-bit, intervalla tensionis/curentis et coniunctorem frontalem 40-polarem ad insertionem praebitam.

Q2. Quomodo novum modulum ab unitate usita vel renovata distinguere possum?

Petite photographias recentes tituli Siemens, corporis, coniunctoris dorsalis, coniunctoris frontalis praebiti, bracchii scutans et terminalium. Observate signa filorum insertorum, abrasiones, titulos mutatos aut accessoria praebita desiderata.

Q3. Quomodo probare possum fornitem esse legitimam et fidem habentem?

Confirmate registrationem societatis, identitatem bancariam congruentem et citationem scriptam quae Siemens, 6ES7532-5NB00-0AB0 et AQ 2xU/I ST nominat. Comparate intervalla output, praecisionem et coniunctorem praebitum cum officiali folio dati Siemens.

Q4. Quae specificationes technicae inspiciendae sunt antequam ematur?

Confirmate suppetitionem 24 V DC, duos canales, intervalla tensionis/currentis requirata, resolutionem 16-bit, praecisionem operationalem ±0.3%, cyclum 3.2 ms, impedantiam oneris, longitudinem cavi, typum coniunctoris et dimensiones 25 x 147 x 129 mm.

Q5. Quae argumenta materialia ante solutionem petenda sunt?

Petere photographias die datae de integro ordine etiquetta, modulo anteriori, conectori posterioris plani, conectori 40-polari inserendi, elemento inductivo, brachio scutans, terminali scutans et emballagio sigillato ad quotationem ligato.

Q6. Potestne aliud modulus analogicum S7-1500 substituere hunc numerum ordinis?

Non automatio. Moduli similes differre possunt in numero canalium, in intervallis, in resolutione, in isolatione, in accuratia, in diagnosticis, in conectoris subministratione et in subsidio pro incursionibus securitatis. Primum configuratio hardware et connexiones recensendae sunt.

Modellos Recommandatos

60 modelli automationis industrialis electi fortuito

CC-PAIL51	B 5X00453G01 Remote I/O Node Controller	2711R-T10T
KJ3241X1-EA1	1C31122G02/1C31125G2	Yokogawa ADV151-E60/D5A00
DS200SDCCG1A	INNPM22	TRICONEX 3623
22B-D4P0N104	Yokogawa AAI143-H50/K4A00	MPC4 200-510-074-113
ProSoft PLX51-DNPS	Emerson A6120	X-PS 01
X20SI4100	TRICONEX 3636R	CC-PDIH01
TDM4.1-020-300-W0	ABB SD833	ProSoft RLX2-IHNF-A
3HAC029896-001	T8151C	KDA3.3-100-3-A00-W1
IC655MDL527	5466-1245	MVME167-032A
X-COM 01 001	F3316	A 5X00419G02 Ethernet Link Controller
80190-220-01-R	160-BA04NSF1	RH916FN
EJA110E-JMS4G-717EB/NF	6 ACS355-03E-15A6-4	EPRO MMS6310
IMDSO14	3HAC057544-006	AI880A
22B-D6P0N104	INIIT13	HCS01.1E-W0008-A-03-B-ET-EC-NN-L4-NN-FW
2711R-T4T	80190-100-01-R	F3 DIO 20/8 02
1761-L32BWA	B 1C31181G02 Remote I/O Module	1769-L23E-QBFC1B
MVME147-012	IEMMU01	FBM246
1336F-BRF50-AA-EN	Emerson PR9268-301-100	HDS03.2-W100N-HS32-01-FW
Yokogawa AAI543-S50/K4A00	80026-044-02	2707-M485P3
T8451C	22B-B012N104	5466-1045