ALL PRODUCTS

Siemens SIMATIC S7-1500 6ES7532-5NB00-0AB0 AQ 2xU/I ST Analog Output Module

Siemens SIMATIC S7-1500 6ES7532-5NB00-0AB0 AQ 2xU/I ST Analog Output Module

SIEMENS | SIMATIC S7-1500

6ES7532-5NB00-0AB0

AQ 2xU/I ST analog output module with two voltage/current channels, 16-bit resolution, 0.3% operational accuracy and channel diagnostics.

LEAD TIME: In stock

WARRANTY: 1 year

Email Inquiry [email protected]

WhatsApp +86 18159889985

Appurtenance:

Overview
Technical Data
Inquiry
Features
Interfaces
Installation
Environment
FAQ
Recommend Models
Recommended Products

Siemens SIMATIC S7-1500 AQ 2xU/I ST

Exact configured model: 6ES7532-5NB00-0AB0

Official product identity

Standard analog output module with two channels in one group, voltage and current output ranges, diagnostics, substitute values and 16-bit resolution. The delivery includes a 40-pole push-in front connector, infeed element, shielding bracket and shield terminal.

Configured geometry

25 mm width, 147 mm height and 129 mm depth; approximate weight 200 g.

Connection package

Two analog output channels support voltage and current loads. Supported ranges include 0 to 10 V, 1 to 5 V, -10 to +10 V, 0 to 20 mA, -20 to +20 mA and 4 to 20 mA.

Installation focus

Install in the S7-1500 rack, connect 24 V DC load voltage, use the supplied push-in front connector, route shielded analog cables through the shielding hardware and parameterize each channel before commissioning.

Procurement check

Match every segment of 6ES7532-5NB00-0AB0. Confirm AQ 2xU/I ST, two channels, 16-bit resolution, included 40-pole push-in connector, voltage/current ranges and exact suffix 5NB00-0AB0.

Technical Data

Official configuration and specifications

Complete model	6ES7532-5NB00-0AB0
Product family	Siemens SIMATIC S7-1500
Product type	AQ 2xU/I ST analog output module
Official description	Two-channel voltage/current analog output module, 16-bit resolution, 0.3% operational accuracy, diagnostics and substitute values
Hardware / firmware	FS01 / V1.0.0
Rated supply voltage	24 V DC; permissible 19.2 to 28.8 V DC
Current consumption	110 mA maximum
Power loss	2.7 W typical
Number of analog outputs	2
Voltage ranges	0 to 10 V; 1 to 5 V; -10 to +10 V
Current ranges	0 to 20 mA; -20 to +20 mA; 4 to 20 mA
Cycle time	3.2 ms minimum for all channels
Resolution	16 bit including sign, with overrange
Conversion time	0.5 ms per channel
Operational accuracy	±0.3% for voltage and current over the full temperature range
Voltage load	Minimum 1 kΩ; 0.5 kΩ for 1 to 5 V
Current load	Maximum 750 Ω
Shielded cable length	Up to 800 m for current; 200 m for voltage
Diagnostics	Supply voltage, wire break for current, short circuit for voltage, overflow/underflow
Front connector	40-pole push-in front connector supplied
Dimensions	25 x 147 x 129 mm (W x H x D)
Weight	Approx. 200 g
Operating temperature	Horizontal: -30 to +60 °C from FS04; vertical: -30 to +40 °C from FS04
Installation altitude	Up to 5,000 m; restrictions above 2,000 m
Official document	Siemens data sheet 6ES7532-5NB00-0AB0, pages 1-3; last modified 2023-08-16

Inquiry

CONTACT

STELLA

Email Inquiry [email protected]

WhatsApp +86 18159889985

Features

Flexible analog outputs

Each of the two channels can be parameterized for supported voltage or current ranges with substitute values and diagnostics.

Precision conversion

The module provides 16-bit resolution, 0.5 ms conversion per channel and ±0.3% operational accuracy over the full temperature range.

Safety-related tripping

From the specified hardware status, standard-module load groups can be shut down for applications up to PL d, Category 3 and SIL 2.

Interfaces

Voltage output modes

Supported voltage ranges are 0 to 10 V, 1 to 5 V and -10 to +10 V with two-wire or four-wire actuator connection.

Current output modes

Supported current ranges are 0 to 20 mA, -20 to +20 mA and 4 to 20 mA with two-wire actuator connection.

Connector and shielding

The supplied 40-pole push-in front connector, infeed element, shielding bracket and shield terminal form the field-wiring interface.

Installation

Rack and load voltage

Mount the 25 mm wide module in the S7-1500 rack and supply 24 V DC within the official 19.2 to 28.8 V range.

Channel wiring

Select the correct voltage or current terminal assignment, observe load impedance and cable-length limits, and connect the cable shield to the supplied shielding hardware.

Parameterization and test

Configure each channel range and substitute value, then verify diagnostics, signal direction and measured output before connecting the final actuator.

Environment

Orientation limits

Horizontal installation is specified up to +60 °C; vertical installation is specified up to +40 °C. Minimum -30 °C values apply from the stated hardware status.

Altitude

Operation is specified up to 5,000 m, with restrictions for installation altitudes above 2,000 m.

Diagnostic monitoring

RUN, ERROR, PWR, channel-status and channel-diagnostic LEDs support commissioning and maintenance inside the control enclosure.

FAQ

Q1. How can I verify the exact 6ES7532-5NB00-0AB0 offered in a quotation?

Check the full order number, AQ 2xU/I ST designation, two analog outputs, 16-bit resolution, voltage/current ranges and the included 40-pole push-in front connector.

Q2. How can I distinguish a new module from a used or refurbished unit?

Request current photos of the Siemens label, housing, backplane connector, supplied front connector, shielding bracket and terminals. Look for inserted-wire marks, scratches, altered labels or missing supplied accessories.

Q3. How should I verify the supplier is legitimate and reliable?

Confirm company registration, matching bank identity and a written quotation identifying Siemens, 6ES7532-5NB00-0AB0 and AQ 2xU/I ST. Compare the output ranges, accuracy and included connector with the official Siemens data sheet.

Q4. Which engineering specifications must be checked before purchase?

Confirm 24 V DC supply, two channels, required voltage/current ranges, 16-bit resolution, ±0.3% operational accuracy, 3.2 ms cycle, load impedance, cable length, connector type and 25 x 147 x 129 mm dimensions.

Q5. What physical evidence should be requested before payment?

Request dated photos of the complete order label, module front, backplane connector, 40-pole push-in connector, infeed element, shielding bracket, shield terminal and sealed packaging tied to the quotation.

Q6. Can another S7-1500 analog output module replace this order number?

Not automatically. Similar modules can differ in channel count, ranges, resolution, isolation, accuracy, diagnostics, connector supply and safety-related tripping support. The hardware configuration and wiring must be reviewed first.

Recommend Models

60 randomly selected industrial automation models

CC-PAIL51	B 5X00453G01 Remote I/O Node Controller	2711R-T10T
KJ3241X1-EA1	1C31122G02/1C31125G2	Yokogawa ADV151-E60/D5A00
DS200SDCCG1A	INNPM22	TRICONEX 3623
22B-D4P0N104	Yokogawa AAI143-H50/K4A00	MPC4 200-510-074-113
ProSoft PLX51-DNPS	Emerson A6120	X-PS 01
X20SI4100	TRICONEX 3636R	CC-PDIH01
TDM4.1-020-300-W0	ABB SD833	ProSoft RLX2-IHNF-A
3HAC029896-001	T8151C	KDA3.3-100-3-A00-W1
IC655MDL527	5466-1245	MVME167-032A
X-COM 01 001	F3316	A 5X00419G02 Ethernet Link Controller
80190-220-01-R	160-BA04NSF1	RH916FN
EJA110E-JMS4G-717EB/NF	6 ACS355-03E-15A6-4	EPRO MMS6310
IMDSO14	3HAC057544-006	AI880A
22B-D6P0N104	INIIT13	HCS01.1E-W0008-A-03-B-ET-EC-NN-L4-NN-FW
2711R-T4T	80190-100-01-R	F3 DIO 20/8 02
1761-L32BWA	B 1C31181G02 Remote I/O Module	1769-L23E-QBFC1B
MVME147-012	IEMMU01	FBM246
1336F-BRF50-AA-EN	Emerson PR9268-301-100	HDS03.2-W100N-HS32-01-FW
Yokogawa AAI543-S50/K4A00	80026-044-02	2707-M485P3
T8451C	22B-B012N104	5466-1045