ALL PRODUCTS

Bently Nevada 3300 146054-034-20-02-05 Ceramic Capped Probe | Original New

Bently Nevada 3300 146054-034-20-02-05 Ceramic Capped Probe | Original New

BENTLY NEVADA · 3300 SERIES 146054-034-20-02-05 3300 Ceramic Capped Probe	CHEMICAL DUTY 3/8-24 UNF 2.0 m cable
Case: 3.4 in · Connector: ClickLoc · Approval option: CSA / ATEX / IECEx Email Inquiry WhatsApp [email protected] \| +86 18159889985

Overview
Technical Data
Interfaces
Environment
Installation
Verification
Availability
Recommended Models
FAQ & Quote
Recommended Products

OFFICIAL PRODUCT OVERVIEW

Ceramic-capped probe for demanding process conditions

Bently Nevada 146054-034-20-02-05 is a 3300 Ceramic Capped Probe intended for aggressive chemical or high-pressure applications. The selected option uses a 3/8-24 UNF case without armor, a 3.4 in overall case length, a 2.0 m standard cable and a miniature coaxial ClickLoc connector.

Alumina ceramic capAISI 304 caseHermetic front seal

Technical Data

MEASUREMENT 1.52 mm Linear range, approximately 0.25–1.78 mm	RECOMMENDED GAP 1.0 mm Electrically gap the probe and avoid tip contact
Pressure rating: 34 bar (500 psi) · Case length: 3.4 in · Total length: 2.0 m (6.6 ft) Approvals option 05: CSA, ATEX and IECEx. Higher-pressure modifications are available from the manufacturer.

Interfaces

CONSTRUCTION

Ceramic-to-metal sensing tip

Probe case: AISI 304 stainless steel, 3/8-24 UNF thread, without armor.
Cable: 75-ohm FEP-insulated coaxial standard cable.
Connector: Gold-plated miniature coaxial ClickLoc connector with finger-tight click mechanism.
System fit: Use with the correct 3300 extension cable and 3300 Proximitor Sensor.

Environment

SERVICE LIMITS

Chemical and temperature boundaries

Temperature
-51 to +177 C operating and storage

Pressure
34 bar (500 psi) standard rating

Approvals
Option 05: CSA, ATEX and IECEx

Rear seal caution: The rear of the 146054 probe is not sealed. Do not expose it to water, ammonia, ammonium hydroxide, hydrogen sulfide or other incompatible media. Confirm process compatibility before installation.

Installation

INSTALLATION CONTROL

Mount, route and gap correctly

1 Mount
3/8-24 UNF; maximum thread engagement 0.563 in.

2 Route
Maintain at least 25.4 mm cable bend radius.

3 Connect
Finger-tighten the ClickLoc connector until it clicks.

4 Gap
Electrically set 1.0 mm recommended gap; avoid tip contact.

Verify the mating extension cable, Proximitor Sensor, target material and hazardous-area requirements against the official manual before commissioning.

Verification

BEFORE ORDER

Verify the complete system

Article code 146054-034-20-02-05, including every option suffix	System components Correct 3300 extension cable and Proximitor Sensor
Installation data Thread, reach, connector clearance and cable route	Process conditions Target material, pressure, temperature and media exposure

Current overall and nameplate photos are available on request. Use the photographed part number and revision to confirm the quoted unit before payment.

Availability

COMMERCIAL CONFIRMATION

Availability is verified per quotation

Stock status	Confirm before quotation
Condition and testing	New, used or refurbished condition and test scope are subject to quoted-unit verification
Photos and nameplate	Available on request for the current unit
Warranty and dispatch	Subject to verification and stated on the quotation
Payment and quote time	Supported methods and response time are confirmed by the sales team

Request a written quotation that identifies the selling company, complete article number, unit condition, photos, test scope, warranty, payment terms and estimated dispatch.

Recommended Models

SYSTEM FAMILY

FAQ & Quote

COMMON QUESTIONS

Confirm the quoted unit before purchase

Is 146054-034-20-02-05 currently available?
Confirm before quotation. Send the complete article number, quantity and destination.

Can I receive current photos and a test statement?
Both are available on request and remain subject to the quoted unit and agreed test scope.

What should be supplied for a compatibility check?
Provide the installed probe, extension cable and Proximitor Sensor numbers, target material, process conditions and required approvals.

Email Inquiry WhatsApp

[email protected] | +86 18159889985