Home > Products > SIEMENS > SIMATIC S7 Series
|
Complete model
|
6ES7134-6GD00-0BA1
|
|
Product family
|
SIMATIC ET 200SP
|
|
Product type
|
AI 4xI 2-/4-wire ST analog input module
|
|
Dimensions
|
15 x 73 x 58 mm (W x H x D)
|
|
Weight
|
31 g
|
|
Analog inputs
|
4 current inputs
|
|
Supported transmitters
|
2-wire or 4-wire current transmitters
|
|
Input ranges
|
0 to 20 mA; 4 to 20 mA; +/-20 mA
|
|
Resolution
|
15 bit for 0 to 20 mA and 4 to 20 mA; 16 bit including sign for +/-20 mA
|
|
Rated load voltage
|
24 V DC
|
|
Current consumption
|
Maximum 37 mA without sensor supply
|
|
Power loss
|
Typical 0.85 W
|
|
Usable BaseUnits
|
Type A0 and A1
|
|
Shielded cable length
|
Maximum 200 m
|
|
Input resistance
|
100 ohms
|
|
Destruction limits
|
50 mA maximum input current; 30 V maximum input voltage
|
|
Basic error limit
|
+/-0.3% at 25 deg C
|
|
Operating error limit
|
+/-0.5% over the specified range
|
|
Conversion times
|
180 ms at 16.6 Hz; 60 ms at 50 Hz; 50 ms at 60 Hz
|
|
Isolation test
|
707 V DC
|
|
Diagnostics
|
DIAG green/red, PWR green, channel status green; readable diagnostic information
|
|
CONTACT
STELLA
|
|
Four-channel input
The module acquires four analog current signals.
|
Flexible transmitters
Channels support 2-wire or 4-wire transmitter connections.
|
|
Measurement selection
Three current ranges are available for common industrial signals.
|
Diagnostics
Module-level diagnostics and channel status indications are provided.
|
|
Terminal assignment
Connection points are defined for the four current input channels and transmitter supply.
|
Shielded cabling
The specified maximum shielded cable length is 200 m.
|
|
Input protection
The documented destruction limits are 50 mA and 30 V at an input.
|
Address space
The module uses 8 bytes of input address space.
|
|
BaseUnit selection
Use an ET 200SP BaseUnit of type A0 or A1.
|
Mechanical coding
Verify the complete article number and compatible BaseUnit before assembly.
|
|
Load voltage
Provide the rated 24 V DC load voltage with correct polarity.
|
Signal wiring
Configure each channel for its actual 2-wire or 4-wire transmitter and current range.
|
|
Electrical isolation
Channels are isolated from the backplane bus; 4-wire channels are isolated from load voltage L+.
|
Potential difference
Maximum documented potential difference is 75 V DC or 60 V AC.
|
|
Signal accuracy
Basic error is +/-0.3% at 25 deg C and operating error is +/-0.5%.
|
Interference rejection
Selectable suppression uses 16.6, 50, or 60 Hz conversion timing.
|
|
Q1. How can I verify the quoted item is exactly 6ES7134-6GD00-0BA1?
Match the full Siemens number on the quotation, module label, and package. Confirm AI 4xI 2-/4-wire ST, four current inputs, 24 V DC load voltage, and BaseUnit type A0 or A1 compatibility.
|
|
Q2. How can I distinguish New, Used, or Refurbished condition?
Request current close-ups of the label, front connector area, channel LEDs, coding element, housing, contacts, and packaging. Require the exact condition and whether seals were opened in writing.
|
|
Q3. How can I check whether a supplier is legitimate and reliable?
Verify company registration, address, bank beneficiary, business contacts, and a formal quotation that lists 6ES7134-6GD00-0BA1 in full with condition, quantity, and traceable identification.
|
|
Q4. Which specifications should an engineer verify before purchase?
Confirm four current inputs, the required 0 to 20 mA, 4 to 20 mA, or +/-20 mA range, 2-wire or 4-wire transmitter wiring, A0 or A1 BaseUnit, 24 V DC load voltage, 15 x 73 x 58 mm size, and 31 g weight.
|
|
Q5. What physical evidence should I request before payment?
Ask for dated photos or video showing the full 6ES7134-6GD00-0BA1 label, hardware status, front channel markings, LEDs, terminal and coding areas, contacts, seals, packaging, and quantity.
|
|
Q6. Can 6ES7134-6GD01-0BA1 or another suffix replace this model?
Do not assume it can. A suffix change may indicate a different hardware revision, measurement performance, compatibility, diagnostics, approvals, or lifecycle status; validate the exact configured module and engineering release.
|
|
253-pvmw
|
ABB SA/S 8.6.1.1 2CDG110153R0011
|
BK3150
|
|
CDP2-CBL-OBD-05
|
VE801R
|
LCAD03VLNOD 1080P
|
|
VCL-E1 VCL-E1-015
|
EST 3-PPS/M-230
|
3G3SV-BB015-E
|
|
IC693ALG391G
|
QBM2030-1U
|
ES0601 lC754VSl06MTD-FF
|
|
MCR-EX-SL-RTD-I-NC
|
BP-2002
|
51-41-RX1
|
|
1000DC-PV-ST
|
DVIVision-ARU-CON-RM A1120070
|
E001-H031007
|
|
SXWAO8XXX10001 AO-8
|
UE4740-22H0000
|
S90-P41110200
|
|
KFD2-SD-Ex1.17
|
926315-BM
|
XRE2024D
|
|
NTB-HD-10-S
|
KFD2-UT2-EX1
|
ABB MA111 DSFS 11A 57791 000-A
|
|
EIR308
|
ZWD020
|
QSNE-4S10-D
|
|
ABB CPU PM582 1SAP140200R0201
|
HT-3015HA
|
WV-S1112
|
|
6GK7243-1JX30-0XE0
|
XL1000C100
|
ABB 1SAJ929200R0060 CEM11-FBP.60
|
|
MGC-PRO-D-500-0500
|
ABB PSM0004 2RCA025059A0001R
|
DCRE12
|
|
MO11AA0E3-01R
|
928NFNTEK000TE RKLB40
|
XDB-C18 7995118-504
|
|
HCD2-FBPS-1
|
2967060 PLC-RSC-24DC/21-21
|
ANN840
|
|
3/24 1A/21S
|
iMZ320
|
SL-2000-P
|
|
STACK-T1-3M , V01 800-40405-01
|
E-E720MBA
|
a36aha-9108
|
|
193-EC2AB
|
NGRX-ELVI-AU-WH
|
cp6607-0001-0000
|
|
Allen Bradley 2711P-RDT7C /C
|
BB101PV BBVRR1RHY2VDL3BX03
|
RK 926 115-an
|
|
GLB136.1E
|
MI-DCMOE
|
ABB TU516/1SAP212000R0001
|
EN
