Home > Products > EMERSON > EMERSON Delta V
|
Complete model
|
VE4003S2B1
|
|
Brand
|
Emerson
|
|
Product family
|
DeltaV M-series Traditional I/O
|
|
Product type
|
HART analog input card with standard I/O termination block
|
|
Number of channels
|
8
|
|
Nominal signal range
|
4 to 20 mA
|
|
Full signal range
|
1 to 22.5 mA with over-range checking
|
|
Isolation
|
Each channel optically isolated from the system; factory tested to 1500 VDC
|
|
Accuracy over temperature
|
0.1% of span
|
|
Resolution
|
16-bit A/D converter
|
|
Repeatability
|
0.05% of span
|
|
Roll-off frequency
|
-3 dB at 2.7 Hz; -20.5 dB at half the sampling frequency
|
|
LocalBus current
|
Simplex: 120 mA typical, 150 mA maximum; redundant: 175 mA typical, 250 mA maximum per card
|
|
Field circuit power
|
300 mA maximum at 24 VDC, +10%
|
|
HART communication
|
Pass-through for AMS Device Manager; variable and status reporting
|
|
HART scan time
|
600 to 800 ms typical per enabled channel
|
|
I/O card keying
|
A1
|
|
Compatible terminal block
|
Standard I/O termination block; fused and 4-wire options listed
|
|
Dimensions
|
H 10.7 x W 4.1 x D 10.5 cm
|
|
Weight
|
Not separately published for VE4003S2B1 in the selected official document
|
|
Protection rating
|
IP20
|
|
Operating temperature
|
-40 to 70 deg C
|
|
Storage temperature
|
-40 to 85 deg C
|
|
Relative humidity
|
5 to 95% non-condensing
|
|
Software note
|
Supported on DeltaV v10.3.1 and later; earlier versions use KJ3222X1-BA2
|
|
Certifications
|
CE, FM, CSA, ATEX, IECEx; marine certifications include IACS E10, ABS and DNV
|
|
Exact marking
|
VE4003S2B1
|
|
Official identity
|
8-channel 4-20 mA HART analog input I/O interface
|
|
Evidence to match
|
Match the complete VE4003S2B1 marking, 8-channel 4-20 mA HART identity, standard termination block and A1 keying.
|
|
System
The card supports simplex or redundant installation. Verify DeltaV v10.3.1 or later for this ordering code, the A1 keying and the required 2-wire standard termination block.
|
Key selection
8 channels | 4-20 mA | HART | 0.1% span accuracy | Key A1
|
Source control
Use the current official Emerson data sheet and confirm the installed carrier, software and revision before substitution.
|
|
Keying
Confirm A1 keying, 4-20 mA loop wiring and transmitter power requirements before installation. Use the standard I/O block for the ordered VE4003S2B1 configuration.
|
Field wiring
Verify polarity, signal range, isolation and the exact terminal-block wiring before energizing.
|
Environment
Maintain the published -40 to 70 deg C operating range, IP20 protection and applicable hazardous-area procedures.
|
|
Identity
Require a clear current photo showing the complete VE4003S2B1 marking.
|
Engineering match
Require the full model label, HART AI identity, standard terminal block, A1 keying, revision and a clear view of all eight channel terminals.
|
Condition evidence
Request label, housing, connector, terminal, keying, seal and packaging photos before payment.
|
|
Recommended Model
|
Recommended Model
|
Recommended Model
|
|---|---|---|
|
CC-PUIO01
|
6ES7288-1SR30-0AA1
|
1756-CN2R
|
|
6ED1052-2MD08-0BA2
|
TU839
|
1756-L64
|
|
1756-IB16
|
6ES7241-1CH32-0XB0
|
1756-EN3TR
|
|
CI522-MODTCP
|
AAV542
|
DI840
|
|
VE3012
|
1756-EN4TR
|
1769-L30ERM
|
|
6ES7288-1CR40-0AA1
|
CI851K01
|
ATSS3S
|
|
6ES7223-1PH32-0XB0
|
6ES7516-3AN02-0AB0
|
PM861AK01
|
|
CI857K01
|
CI868K01
|
VE4005S2B4
|
|
1756-L72
|
6ES7550-1AA01-0AB0
|
6ES7592-1AM00-0XB0
|
|
6ES7288-1CR20-0AA1
|
1756-L83ES
|
ASD143
|
|
6ED1055-1FB00-0BA2
|
TP830
|
6ES7332-5HD01-0AB0
|
|
6ES7542-1AX00-0AB0
|
6ES7288-6EC01-0AA0
|
KJ2002X1-BA1
|
|
TB850
|
CC-GAIX11
|
1769-L16ER-BB1B
|
|
6ES7392-1AJ00-0AA0
|
ADV142
|
6ES7515-2AM02-0AB0
|
|
PM582-ETH
|
6ES7292-1AG30-0XA0
|
CI860K01
|
|
AAV142
|
6ES7288-3AT08-0AA0
|
6EP3331-6SB00-0AY0
|
|
6ES7215-1AG40-0XB0
|
6ES7288-1SR40-0AA1
|
5069-L330ERM
|
|
KJ3203X1-BA1
|
CI856K01
|
KJ3204X1-BA1
|
|
DI562
|
6ES7288-1ST60-0AA1
|
6ES7505-0RB00-0AB0
|
|
6ES7512-1DK01-0AB0
|
6ES7288-1CR30-0AA1
|
6ES7518-4JP00-0AB0
|
EN
