ALL PRODUCTS

Bently Nevada 3300 XL NSv 330901-04-24-10-02-05 Standard Mount Proximity Probe

Bently Nevada 3300 XL NSv 330901-04-24-10-02-05 Standard Mount Proximity Probe

BENTLY NEVADA | 3300 XL NSV

330901-04-24-10-02-05

3300 XL NSv Standard-Mount Proximity Probe, 1/4-28 UNF thread, without armor

CONFIGURATION: 0.4 in unthreaded length | 2.4 in case | 1.0 m probe | ClickLoc connector | Multiple approvals

LEAD TIME: In stock

WARRANTY: 1 year

Email Inquiry [email protected]

WhatsApp +86 18159889985

Appurtenance:

bently nevada 3300 xl nsv 330901 04 24 10 02 05 standard mount proximity probe-1

Overview
Technical Data
Inquiry
Construction
Installation
Selection Guide
Environment
FAQ
Recommend Models
Recommended Products

Bently Nevada 3300 XL NSv Standard-Mount Probe

Exact configured model: 330901-04-24-10-02-05

Official product identity

The 330901 is a 3300 XL NSv standard-mount proximity probe with a 1/4-28 UNF-2A thread and no armor. The NSv design is intended for restricted counterbore, side-view and rear-view installations and for small targets.

Configured geometry

Option A:04 sets 0.4 in unthreaded length and option B:24 sets 2.4 in overall case length. The probe-tip diameter is 5.26 mm maximum and the selected total probe length is 1.0 m.

Connection package

Option D:02 supplies a miniature coaxial ClickLoc connector with standard cable and no connector protector. Option E:05 specifies multiple approvals.

Installation focus

Observe the 1/4-28 thread-engagement limit, minimum 25.4 mm cable bend radius and recommended 1.0 mm system gap. The probe must be used with a matching NSv extension cable and Proximitor Sensor.

Procurement check

Match every segment of 330901-04-24-10-02-05. The unthreaded length, case length, total probe length, connector/cable type and approval option must all match; other 330901 suffixes alter mechanical reach or connectivity.

Technical Data

Official configuration and specifications

Complete model	330901-04-24-10-02-05
Product family	Bently Nevada 3300 XL NSv
Product type	Standard-mount proximity probe without armor
Case thread	1/4-28 UNF-2A
Unthreaded length	0.4 in (10.2 mm), option 04
Overall case length	2.4 in (61.0 mm), option 24
Total probe length	1.0 m (39 in), option 10
Connector and cable	Miniature coaxial ClickLoc connector, standard cable, no connector protector (option 02)
Agency approval	Multiple approvals (option 05)
Probe tip material	Polyphenylene sulfide (PPS)
Probe case material	AISI 304 stainless steel
Dimensions	Probe tip diameter 5.26 mm (0.207 in) maximum; selected case length 61.0 mm; selected unthreaded length 10.2 mm
Weight	Approximately 14 to 150 g (0.5 to 5.3 oz), probe range
Minimum bend radius	25.4 mm (1.0 in)
Operating and storage temperature	-52 to +177 °C (-62 to +351 °F)
Recommended gap	1.0 mm (40 mils) within the matched NSv system
Official document	Datasheet 147385 Rev. R, pages 1–3, 5–6, 8, 11 and 30

Inquiry

CONTACT

STELLA

Email Inquiry [email protected]

WhatsApp +86 18159889985

Construction

Probe tip

The NSv probe uses a PPS tip with a maximum diameter of 5.26 mm, supporting installations where space and side-view restrictions limit larger probes.

Probe case

The standard-mount case is AISI 304 stainless steel with a 1/4-28 UNF-2A external thread. This 330901 version is supplied without armor.

Cable assembly

The selected probe has a 1.0 m, 75-ohm FEP-insulated coaxial standard cable and a miniature male coaxial ClickLoc connector.

Selected geometry

The order code specifies 0.4 in unthreaded length and 2.4 in overall case length; both dimensions must be checked against the mounting bracket or tapped hole.

Installation

Thread engagement

For a 1/4-28 probe, the official maximum thread engagement is 0.375 in. Excessive engagement can cause binding and is not covered as a probe warranty failure.

Cable routing

Maintain at least the 25.4 mm minimum bend radius and protect the unarmored standard cable from abrasion, tension and sharp edges.

Matched system

Combine the 1.0 m probe with the correct NSv extension cable so probe plus extension cable equals the selected Proximitor Sensor system length.

Gap and target

Use the matched 3300 XL NSv system with an appropriate steel target. The recommended gap setting is 1.0 mm and the nominal linear range is 1.5 mm under specified conditions.

Selection Guide

330901

3300 NSv probe, 1/4-28 UNF thread, without armor.

04 | Unthreaded length

0.4 in (10.2 mm).

24 | Case length

2.4 in (61.0 mm).

10 | Total length

1.0 m (39 in).

02 | Connector and cable

ClickLoc connector with standard cable, without connector protector.

05 | Approval

Multiple approvals.

System compatibility

Use with a matching 3300 XL NSv extension cable and Proximitor Sensor.

Environment

Probe temperature

Operating and storage range is -52 to +177 °C. Sustained exposure below -34 °C may cause premature pressure-seal failure.

Humidity context

The matched NSv system is specified for 100% condensing, non-submersible conditions when connectors are protected.

Materials

The probe tip is PPS, the probe case is AISI 304 stainless steel and the connector uses gold-plated brass.

Approval scope

Option 05 selects multiple approvals. Verify the exact country and product approval listing in the official Approvals Quick Reference Guide before representing a specific certification.

FAQ

Q1. How do I confirm the exact 330901 probe being quoted?

Require 330901-04-24-10-02-05 on the probe or packing label and quotation. Decode 0.4 in unthreaded length, 2.4 in case, 1.0 m total length, option 02 ClickLoc standard cable and multiple approvals.

Q2. How can New, Used and Refurbished probes be distinguished?

Request dated macro photos of the PPS tip, 1/4-28 threads, stainless case, cable jacket, ClickLoc connector and label. Check for wrench flats damage, bent cable, contamination, thread wear or reworked identification.

Q3. How should the supplier be qualified?

Verify legal registration, business address, bank beneficiary and traceable contact records. Require exact-model photographs and compare the suffix code with datasheet 147385 Rev. R before payment.

Q4. Which engineering checks are essential before purchase?

Confirm the 1/4-28 mounting thread, 0.4 in unthreaded section, 2.4 in case, 1.0 m cable, standard cable type, matching NSv system length, target material and available counterbore.

Q5. What proof should be requested before payment?

Obtain a dated continuous video or photo set showing the full order code, probe tip, thread, case geometry, 1.0 m lead, ClickLoc connector and evidence that the cable is unarmored and has no connector protector.

Q6. Can a different 330901 suffix or an armored probe substitute?

Not automatically. Different A/B lengths change mechanical reach, while connector, FluidLoc, protector, armor and approval options alter installation and compatibility. Engineering approval is required.

Recommend Models

60 randomly selected industrial automation models

ProSoft PLX31-PND-MBS4	1769-L23E-QBFC1B	CMC16 200-530-022-014
X-COM 01 001	SPASI23	Emerson A6312
RH916FN	2711R-T4T	Siemens 6ES7522-1BH10-0AA0
IEMMU01	T8850C	3HAC058993-004
80190-480-01-R	3HAC029896-001	B 5X00453G01 Remote I/O Node Controller
Yokogawa ADV151-E60/D5A00	DS200SDCCG1A	2707-V40P2N
16 ACS580-01-206A-4	1783-BMS10CGP	1336F-BRF50-AA-EN
CC-PUIO31	2711P-T12C4D8	INNPM22
2707-M485P3	6 ACS355-03E-15A6-4	Edge Controller IC695CPL410
VersaMax CPU IC200CPUE05	HCS01.1E-W0008-A-03-B-ET-EC-NN-L4-NN-FW	5466-1141
22B-D4P0N104	DS3800NDAC1B1C	MPC4 200-510-076-114
X20CP0483	RH928CY	TDM4.1-020-300-W0
INIIT13	F3 DIO 20/8 02	22B-D6P0N104
Emerson PR9268-301-100	MVME167-032A	80190-100-01-R
PM554-TP-ETH	Yokogawa S2MMM843-SS1130	CC-PCNT02
FCM2F4	IMDSO14	80026-044-02
160-BA04NSF1	EPRO MMS6312	IC655MDL527
DS200DMCBG1A	3HAC058612-00	KJ3241X1-EA1
X20PS9402	1C31122G02/1C31125G2	T8151C
TRICONEX 3703E	EJA110E-JMS4G-717EB/NF	PM591-2ETH