| Sales | Phone/Whatsapp | |
| Jim Pei | [email protected] | +86 18020776782 |
| Model Number | 6DL1136-6AA00-0PH1 |
| Analog Current Inputs | 8 |
| Input Resolution including Sign | 16 bit |
| Rated Supply | 24 V DC |
| Permissible Supply | 19.2–28.8 V DC |
| Rated Current without Sensor Supply | 90 mA |
| Sensor Supply Outputs | 8 |
| Maximum Sensor Supply per Channel | 30 mA |
| Backplane Power | 90 mW |
| Typical Power Loss | 2.8 W |
| Input Address Space | 22 bytes |
| Output Address Space | 5 bytes |
| Input Destruction Limit | 35 mA |
| Supported Input Ranges | 0–20 mA / 4–20 mA |
| Current Input Resistance | 150 Ω |
| Maximum Shielded Cable | 1,000 m, twisted pair |
| Measurement Principle | Sigma Delta |
| Integration Time at 50 Hz | 20 ms |
| Integration Time at 60 Hz | 16.66 ms |
| Smoothing Stages | 1 / 4 / 16 / 64 conversion cycles |
| Minimum Input Crosstalk | -70 dB |
| Steady-state Repeat Accuracy at 25 °C | ±0.008% of input range |
| Maximum Safety Accuracy at 40 °C | 0.6%, 0.7% vertical |
| Maximum Safety Accuracy at 70 °C | 0.9% |
| HART Signal Influence | 0.11% of input range |
| Series-mode Rejection | At least 40 dB |
| Maximum Common-mode Voltage | 35 V |
| Common-mode Rejection | At least 80 dB |
| HART Revision Support | Up to Revision 7 |
| Permissible Input Potential Difference | 30 V DC / 25 V AC |
| Backplane/Load Isolation Test | 1,500 V DC |
| Channel/Load Isolation Test | 370 V AC |
| Safety Performance Level | PL d; PL e with 1oo2 voting on F-CPU |
| Horizontal Operating Temperature | -40–70 °C |
| Vertical Operating Temperature | -40–60 °C |
| Minimum Order Quantity | 1 Piece |
| Price | Contact for Jim |
| Packaging Details | Original new Factory Sealed |
| Delivery Time | 3–7 Days |
| Payment Terms | T/T |
| Shipping Method | DHL / FedEx / UPS / TNT |
| Supply Ability | In stock |
Siemens 6DL1136-6AA00-0PH1 is the fail-safe F-AI current-input module for SIMATIC ET 200SP HA process I/O. It acquires analog current signals from supported two-wire and four-wire transmitters while providing HART communication. The module is intended for an appropriately configured safety-oriented automation system. Redundant operation depends on the specified terminal-block arrangement. Channel diagnostics help locate signal and supply faults during commissioning and service. The required voting arrangement and terminal-block type must be checked against the safety application before ordering.
Acquires current-transmitter signals for the configured fail-safe process automation task.
Combines analog measurement with supported HART communication to the connected field devices.
Supports redundant module operation with the specified F1 terminal-block configuration.
Accommodates supported two-wire and four-wire current transmitters.
Detects wire break, short circuit and signal overflow or underflow for diagnostic handling.
Uses configurable integration and smoothing to match the signal-processing requirements.
No. The technical data qualifies PL e by 1oo2 voting on the F-CPU; the complete safety design must be assessed.
The specified redundancy arrangement uses terminal-block type F1. Check the actual station build.
Yes. An external load may be needed to reach the specified total impedance for an external secondary master.
Request clear channel-connector and nameplate photos with available inspection records for the quoted module.
Provide the terminal-block and safety-system details; confirmed matching stock is released after payment.
Send the transmitter wiring, required redundancy and safety voting details to support a correct configuration review.
Most products are covered by a warranty of up to 12 months, subject to the applicable terms and conditions. If any product-related issue occurs during the warranty period, our team will assist you and provide an appropriate solution.
Relevant datasheets and technical literature can be provided with the goods, offering useful information for product identification, installation, operation, and maintenance.
We understand the importance of minimizing equipment downtime. Our team responds promptly to inquiries and provides professional assistance with product information, quotations, order status, shipping, and after-sales questions.
We serve customers worldwide and provide reliable assistance from inquiry to delivery and after-sales service, ensuring clear and timely communication throughout the process.
We continue to source discontinued, obsolete, and hard-to-find automation parts from various brands, helping customers maintain existing equipment and reduce downtime caused by spare parts shortages.
|
DP2500-R8
|
FP0-C16T FP0-E8RS
|
SN3101
|
|
VLM-000-SIE
|
5906GY
|
DCJ4501-01PLF PSU-350-AC
|
|
DI32R-L
|
3HE05894AAAA01
|
G4HFRN-S7
|
|
5504GI
|
PRO32IN 10290-0000-F REV-C
|
HEX70B-RX
|
|
ITM 4C-6E
|
OAW-AP1201H-RW
|
LIP-ME201 100Base-T
|
|
5NCLPT-2E
|
MDR-20-5
|
SAVI 440 W440-M
|
|
TTS-SD-LCD-B-1
|
Mid2E-800
|
PXA30-K11
|
|
Xm30 X13651469010
|
Nov-33
|
M21NSXA-LDN-HD-02
|
|
MB-402
|
DM92
|
GV-U6E
|
|
AV5155DN
|
C-MAP M-IN-M201.07
|
VT5400
|
|
TSXDSY64T2K
|
2CDG 110 064 R0011
|
EGX100MG
|
|
N3511RA-M
|
DMC-4k-HDO
|
GCU-HOSP-1
|
|
MF6FTJ0026
|
ET1111-F-MT 10/100M
|
SNZ4052K R1.188.0960.0
|
EN
