ALL PRODUCTS

Bently Nevada 3300 XL 8 mm 330105-02-12-05-02-05 Reverse Mount Probe | Original New

Bently Nevada 3300 XL 8 mm 330105-02-12-05-02-05 Reverse Mount Probe | Original New

BENTLY NEVADA · 3300 XL 8 MM

330105-02-12-05-02-05

3/8-24 UNF reverse-mount probe, 0.5 m lead, ClickLoc standard cable, CSA, ATEX and IECEx approvals.

CONFIGURATION 30 mm case / 0.5 m lead	INTERFACE 3/8-24 UNF / ClickLoc
LEAD TIME In stock	WARRANTY 1 year

Email Inquiry [email protected]

WhatsApp +86 18159889985

Appurtenance:

bently nevada 3300 xl 8 mm 330105 02 12 05 02 05 reverse mount probe original new-1

Overview
Technical Data
Inquiry
Applications
Construction
Installation
Selection
FAQ
Recommend Models
Recommended Products

3/8-24 UNF REVERSE-MOUNT PROXIMITY PROBE

3/8-24 UNF / ClickLoc

A reverse-mount 8 mm proximity probe for tight-access machinery measurements, with a 3/8-24 UNF thread, 0.5 m standard lead and approved installation option.

DOCUMENTED MODEL
330105-02-12-05-02-05

SYSTEM FAMILY
3300 XL 8 MM

PRIMARY VALUE
30 mm case / 0.5 m lead

Technical Data

330105-02-12-05-02-05 Technical Data

Officially documented configuration and performance data.

Complete model	330105-02-12-05-02-05
Product family	Bently Nevada 3300 XL 8 MM Transducer System
Product type	3/8-24 UNF reverse-mount proximity probe
Dimensions	8.0 mm tip; 7/16 in hex; 3/8-24 UNF-2A thread; 5.0 mm unthreaded length; 30 mm case; 0.5 m total length
Weight	Approximately 162 g, calculated from the official 323 g/m probe mass value for a 0.5 m lead
Linear range	2.0 mm (80 mils), approximately 0.25 to 2.3 mm
Recommended gap	1.27 mm (50 mils)
Scale factor	7.87 V/mm (200 mV/mil)
Frequency response	0 to 10 kHz, +0 / -3 dB
Cable	75 ohm cable; 3.68 mm outside diameter
Connector	7.24 mm maximum outside diameter miniature coaxial ClickLoc
Probe materials	PPS tip; AISI 303 or 304 stainless steel case
Total length tolerance	+30% / -0% for the 0.5 m lead
Approval option	05: CSA, ATEX and IECEx approvals

Inquiry

CONTACT

STELLA

Email Inquiry [email protected]

WhatsApp +86 18159889985

Applications

Where this configuration fits and why it is selected.

Reverse mounting Supports installations where the probe must be secured from the rear of a machine bracket or housing.	Shaft vibration Measures dynamic shaft motion in a complete matched 3300 XL 8 mm transducer system.
Position and phase Supports static position, Keyphasor phase reference and speed measurements when correctly arranged.	Restricted access The 8 mm tip and reverse-mount body suit compact machinery clearances.

Construction

Documented materials, mechanical build and signal interfaces.

Probe tip 8.0 mm PPS sensing tip with a 7/16 in hex for handling.	Case and thread AISI 303 or 304 stainless steel reverse-mount case with 3/8-24 UNF-2A thread.
Cable 0.5 m standard 75 ohm cable with 3.68 mm outside diameter.	Connector Miniature coaxial ClickLoc connector with 7.24 mm maximum outside diameter.

Installation

Mounting and Commissioning

A controlled sequence for installation and acceptance.

01 Confirm reverse mount Verify the 3/8-24 UNF-2A bracket thread, rear access and 30 mm case envelope.	02 Set the gap Establish the recommended 1.27 mm gap within the 2.0 mm linear range.
03 Route the lead Protect the 0.5 m standard cable and preserve the specified bend and side clearances.	04 Match the system Select the extension cable and 3300 XL 8 mm Proximitor Sensor for the intended total electrical length.

Selection

Ordering Code Decoded

Each suffix identifies a physical, electrical or approval choice.

330105	3300 XL 8 mm reverse-mount proximity probe
02	3/8-24 UNF-2A thread
12	Reverse-mount case configuration
05	Total length: 0.5 m
02	Miniature coaxial ClickLoc connector with standard cable
05	CSA, ATEX and IECEx approvals

FAQ

BUYER AND ENGINEER CHECKLIST

Six model-specific checks for sourcing and technical acceptance.

Q1. How can a buyer verify the exact quoted model?

Require 330105-02-12-05-02-05 on the quotation and current label evidence. It defines a 3/8-24 UNF reverse-mount probe, 0.5 m lead, standard ClickLoc cable and approval option 05.

Q2. How can New, Used and Refurbished condition be distinguished?

Request dated close views of the 8 mm tip, 3/8-24 thread, hex, full 0.5 m lead, ClickLoc connector and label. Thread wear, cable repairs or altered approvals require explanation.

Q3. How should an industrial buyer qualify the supplier?

Confirm legal entity, payment beneficiary and traceability, then require current proof of this exact reverse-mount ordering code and its approval markings.

Q4. What must engineering confirm before purchase?

Confirm reverse-mount geometry, 3/8-24 UNF thread, 30 mm case, 5 mm unthreaded section, 0.5 m lead, target material, clearances and matched 3300 XL 8 mm system length.

Q5. What evidence should be requested before payment?

Ask for dated full-unit and nameplate photos, tip, thread, connector and cable close-ups, packaging identifiers, approval markings and any agreed continuity or loop-response record.

Q6. Can a standard-mount or different suffix be substituted?

Not automatically. Reverse-mount geometry, thread, lead length, connector and approvals can differ, so engineering must compare every suffix and the installed bracket.

Recommend Models

Recommend Model

DA63M-30C9/0	58B-50/25-AA-PT-51	QS5.241
NJ6-22-NG	MA1472C	DT-72
2CDG110091R0011	GHG4101901R0295	517-0147-06B-318727
419D	4111A	A140-5103
ET-788	W1-S35	295452-PR
AEA4212PB00	ALL-PI2011BP-60W	RCDT320
K63605	LN15SE2-1243	857-400
VG-GFX1	T8800-TB21-9JS0-B0	TM3DQ16UG
6ES7322-8BH01-0AB0	A7708LT50-DWDM	744-98065-00P
415/I/TNS	01701-9	1783-US5T
VEP1485	VJP-4E	176F3423
DRCDD-0L0	MTWP-2475W-FR	HR600-AF-21F-T
AC010S	G2PF400VS02	MBC5100
LAS3	RPM-130-AC-UK	PW481-50-S2
DM-RMC-4K-100-C-1G-B-T	994-14D	ES2008
LIOB-452	KP551	950-0650
SQ121B6220	SPIDER-PL-20-07T1M2M299TWVHHHH	MS-VMA1615-0
LP-XP91D02-000C	72604R-TP/XF-1250	3.902.103.670
WIS-50	PSI-MOS-RS232/FO	M1-201SA-TR
07-7331-2302	6ED1055-1MD00-0BA2	A12-FC-XX-C1