|
LEAD TIME: In stock
|
WARRANTY: 1 year
|
8-Channel 4-20 mA HART Analog Output Assembly with Redundant Standard I/O Termination Block. The complete ordering identity must remain associated with its documented mechanical, electrical, environmental and approval configuration.
Core selling point: Redundant DeltaV analog output operation with automatic switchover and an A4-keyed 8-channel HART interface.
Official source: DeltaV M-series Traditional I/O, March 2026, pages 1, 4, 11, 26 and 30. Open datasheet PDF
|
Complete model
|
VE4035S2B1
|
|
Brand
|
Emerson
|
|
Product family
|
DeltaV M-series Traditional I/O
|
|
Product type
|
Redundant standard I/O termination block for an 8-channel analog output card
|
|
Dimensions
|
10.7 x 4.1 x 10.5 cm (4.2 x 1.6 x 4.1 in), common M-series I/O interface dimensions
|
|
Weight
|
Not separately specified in the official product data sheet
|
|
Number of channels
|
8
|
|
Nominal signal range
|
4 to 20 mA
|
|
Full signal range
|
1 to 23 mA
|
|
HART support
|
HART analog output interface
|
|
LocalBus current
|
100 mA typical; 150 mA maximum at 12 VDC nominal per card
|
|
Field circuit power
|
300 mA maximum at 24 VDC ±10% per card
|
|
Accuracy over temperature
|
0.25% of span
|
|
Resolution
|
12-bit
|
|
Isolation
|
Each channel optically isolated and factory tested to 1500 VDC
|
|
Output compliance
|
20 mA at 21.6 VDC supply into a 700 ohm load
|
|
I/O keying
|
A4
|
|
Operating temperature
|
-40 to +70 °C (-40 to +158 °F)
|
|
Storage temperature
|
-40 to +85 °C (-40 to +185 °F)
|
|
Relative humidity
|
5 to 95%, non-condensing
|
|
Protection rating
|
IP20
|
|
Shock and vibration
|
10 g half-sine for 11 ms; 1 mm peak-to-peak from 5 to 16 Hz and 0.5 g from 16 to 150 Hz
|
|
Compatibility
|
DeltaV v10.3.1 and later
|
|
Catalog model
|
VE4035S2B1
|
|
I/O function
|
Analog output, 8 channels, 4 to 20 mA, HART
|
|
Terminal block
|
Redundant standard I/O termination block
|
|
Card keying
|
A4
|
|
System family
|
DeltaV M-series Traditional I/O
|
|
Software baseline
|
DeltaV v10.3.1 or later
|
|
Carrier position
|
Install only in a compatible DeltaV M-series Traditional I/O carrier position.
|
|
Keying
|
Verify the A4 mechanical key before inserting the analog output card.
|
|
Redundancy
|
Use the two-wide redundant terminal-block arrangement so the controller recognizes the pair.
|
|
Power and wiring
|
Provide 24 VDC field circuit power within ±10%, observe the 300 mA per-card limit and wire channels for 4 to 20 mA service.
|
|
DeltaV version
|
Supported on DeltaV v10.3.1 and later.
|
|
I/O card
|
8-channel 4 to 20 mA HART analog output card with A4 keying.
|
|
Termination
|
Redundant standard I/O termination block; not the simplex, fused, 16-pin mass or Series 2 Plus options.
|
|
Carrier family
|
M-series Traditional I/O; the official PDS states M-series Traditional I/O cards are not physically compatible with S-series controller carriers.
|
|
1756-EN4TR
|
6ES7241-1AH32-0XB0
|
5069-L306ERMS2
|
|
CM577-ETH
|
ADV561
|
AI810
|
|
CC-TCF911
|
1756-CN2R
|
CI860K01
|
|
6ES7288-1SR20-0AA1
|
PM864AK01
|
KJ3001X1-BA1
|
|
DO561
|
6ED1055-1FB10-0BA2
|
6ES7288-1ST20-0AA1
|
|
KJ2003X1-BK1
|
1756-OF8
|
1756-DNB
|
|
CC-TDOB01
|
6ES7288-1CR60-0AA1
|
DI840
|
|
6ES7531-7KF00-0AB0
|
VE4005S2B4
|
6ES7332-5HF00-0AB0
|
|
1769-L24ER-QB1B
|
6ES7414-3EM07-0AB0
|
PM856K01
|
|
DI820
|
1756-PA72
|
6ES7511-1CK01-0AB0
|
|
5069-L340ERMS2
|
6ES7521-1BL00-0AB0
|
CC-TCNT04
|
|
6ES7288-1ST30-0AA1
|
CC-PAIH01
|
6ES7288-1CR60-0AA0
|
|
PM571-ETH
|
KJ3002X1-BC1
|
DI524
|
|
6ES7407-0KR02-0AA0
|
CI851K01
|
AAV544
|
|
6ES7288-2DT08-0AA0
|
AX522
|
CI865K01
|
|
5069-L340ER
|
1756-L71
|
DO562
|
|
6ES7531-7QD00-0AB0
|
6ES7223-1BL32-0XB0
|
DO890
|
|
6ES7322-8BF00-0AB0
|
6ES7288-5BA01-0AA0
|
6ES7288-1ST40-0AA1
|
|
5069-L320ERM
|
5069-L320ER
|
KJ3241X1-BA1
|
|
6ED1052-2FB08-0BA2
|
6ES7288-2DT16-0AA0
|
6ES7231-5PD32-0XB0
|