Home > Products > SIEMENS > SIMATIC S7 Series
|
Complete model
|
6ES7132-6BF61-0AA0
|
|
Product family
|
SIMATIC ET 200SP digital output modules
|
|
Product type
|
DQ 8x24V DC/0.5A Sink Basic digital output module
|
|
Type designation
|
DQ 8x24VDC/0.5A SNK BA
|
|
HW functional status
|
From FS02
|
|
Firmware version
|
V0.0; firmware update not possible
|
|
BaseUnit compatibility
|
BU type A0
|
|
Color code
|
CC01
|
|
Supply voltage
|
24 V DC; permissible range 19.2 to 28.8 V
|
|
Current consumption
|
30 mA rated and maximum
|
|
Power loss
|
1.5 W typical
|
|
Digital outputs
|
8 parameterizable sink outputs, NPN M-switching
|
|
Output rating
|
24 V DC; 0.5 A per channel; 4 A maximum per module
|
|
Short-circuit protection
|
Yes; typical response threshold 1.5 A
|
|
Switching frequency
|
100 Hz resistive; 0.5 Hz inductive; 10 Hz lamp load
|
|
Output delay
|
300 us maximum from 0 to 1; 600 us maximum from 1 to 0
|
|
Cable length
|
Up to 1,000 m shielded or 600 m unshielded
|
|
Address space
|
1 output byte
|
|
Diagnostics
|
Supply-voltage monitoring, group error, diagnostic alarm, and substitute values
|
|
Isolation
|
707 V DC type test; channels isolated from backplane bus
|
|
Operating temperature
|
-25 to 60 deg C horizontal; -25 to 50 deg C vertical
|
|
Installation altitude
|
Up to 5,000 m with restrictions above 2,000 m
|
|
Dimensions
|
15 x 73 x 58 mm (W x H x D)
|
|
Weight
|
Approximately 30 g
|
|
Engineering
|
TIA Portal V14; STEP 7 V5.5 SP3; PROFINET GSDML V2.3
|
|
Sink output operation
Eight NPN M-switching channels sink load current and are individually parameterizable for 24 V DC operation.
|
Load capability
Each channel is rated to 0.5 A and the total module output current is rated to 4 A.
|
|
Output protection
Short-circuit protection has a typical 1.5 A response threshold and inductive shutdown voltage is limited to about 47 V.
|
Fallback behavior
Substitute values can be connected for defined output behavior during communication or controller faults.
|
|
BaseUnit interface
The module fits ET 200SP BaseUnit type A0 and uses mechanical coding element type B.
|
Field outputs
Eight current-sinking outputs are provided; current-sourcing operation is not supported.
|
|
Cable capability
Specified cable length is up to 1,000 m shielded or 600 m unshielded.
|
Address mapping
The eight channels occupy one output byte in the ET 200SP station.
|
|
Supply monitoring
The module diagnoses supply-voltage status and provides a green PWR indicator.
|
Module diagnostics
A green or red DIAG LED reports module-level status and group errors.
|
|
Channel indication
Each output channel has a green status indicator; channel-specific diagnostics are not provided.
|
Diagnostic alarm
Diagnostic alarms and substitute values are supported; wire-break and short-circuit diagnosis are not channel-reported.
|
|
Compact dimensions
The module measures 15 x 73 x 58 mm and weighs approximately 30 g.
|
BaseUnit selection
Install only on a compatible type A0 BaseUnit and observe CC01 color coding.
|
|
Ambient orientation
Horizontal operation is specified to 60 deg C and vertical operation to 50 deg C.
|
Engineering requirement
Configure with TIA Portal V14, STEP 7 V5.5 SP3, or the applicable PROFIBUS or PROFINET device description.
|
|
Q1. How can I verify that the quoted item is exactly 6ES7132-6BF61-0AA0?
Match the complete number on the quotation, module label, packaging, and invoice. Confirm DQ 8x24VDC/0.5A SNK BA, NPN sink output, BU type A0, CC01, and the 15 mm width.
|
|
Q2. How can I distinguish a new sink output module from a used or refurbished unit?
Request current photos of the Siemens label, coding element, BaseUnit contacts, front terminals, rail interface, LEDs, and packaging. Check for terminal insertion marks, damaged contacts, discoloration, relabeling, or resealing.
|
|
Q3. How should a buyer verify that the supplier is legitimate and reliable?
Confirm the legal entity, registration, address, bank beneficiary, business contacts, and ET 200SP supply references. All commercial documents should consistently identify 6ES7132-6BF61-0AA0.
|
|
Q4. Which specifications should an engineer verify before purchasing?
Verify eight 24 V DC NPN sink outputs, 0.5 A per channel, 4 A module total, BU type A0, CC01, one-byte mapping, 15 x 73 x 58 mm dimensions, and approximately 30 g weight.
|
|
Q5. What physical evidence should be requested before payment?
Request timestamped images or video showing the complete label, output markings, coding element, BaseUnit contacts, housing, indicators, packaging, and any included accessories.
|
|
Q6. Can a source-output or another DQ suffix replace 6ES7132-6BF61-0AA0?
Not automatically. PNP source and NPN sink outputs use different switching logic, and other suffixes can change diagnostics, BaseUnit type, color coding, current rating, or channel count. Engineering must validate the field circuit.
|
|
1230/stb aci1230
|
RACUB2L
|
4269-593
|
|
7800IDA2Q-3G
|
SSM-15-G
|
1054BPH
|
|
PR120.03
|
ION7300-DISPLAY
|
6504877
|
|
SDL800
|
3DT-NCMCU1.88
|
1756-N2
|
|
SPS-6.5E
|
MC-1110-8M05A20
|
417831G/2
|
|
485opdr RS485
|
FX-PCG2621-0
|
VG-301
|
|
D254.DIN.110.US
|
ABB AX522
|
REV.1.2.021
|
|
PFD-402-N1
|
IC:AB444200035
|
375010
|
|
ABB AI531 / 1SAP250600R0001
|
0004A3C138EA
|
AAM11-S2
|
|
XP2-GKDPB
|
SAC7X00-4000CR
|
HRC5LT20
|
|
MTWP-2475W-FR
|
2CDG 110 062 R0011
|
BUF-2A
|
|
LVOS-0-10-PWM-DIN
|
57D-15-126AA
|
IC200UDR010
|
|
CLFA300LB0C
|
1746-P3
|
DH 100
|
|
MSR3
|
67CFR-224
|
81545-01
|
|
1757-SRC1
|
CW-ANT-O1-NS-00
|
HLF399S 323093
|
|
3900-02-10 PT100
|
FO-10
|
6ES7321-1BH02-0AA0
|
|
Acromag 206245
|
TSXSCY21601
|
400 71 361 055
|
|
MNB-CNTLR-300
|
AR8442
|
H142402
|
|
VLC-16160Z-KH
|
VIO-25/60
|
ABB SACE SD-P2 701693/801
|
|
Televes 502905
|
STBNIP2311
|
046-00093-01 808-8214
|
EN
