ALL PRODUCTS

Siemens SIMATIC ET 200SP 6ES7132-6GD51-0BA0 RQ 4x24 VUC/2 A CO Standard Relay Output Module | Original New

Siemens SIMATIC ET 200SP 6ES7132-6GD51-0BA0 RQ 4x24 VUC/2 A CO Standard Relay Output Module | Original New

SIEMENS SIMATIC ET 200SP

6ES7132-6GD51-0BA0

RQ 4x24 VUC/2 A CO Standard relay output module

OUTPUTS: 4 floating relay changeover contacts

RATING: 24 V AC/DC, 2 A

BASEUNIT: Type A0

LEAD TIME: In stock | WARRANTY: 1 year

Email Inquiry [email protected]

WhatsApp +86 18159889985

Appurtenance:

Overview
Technical Data
Inquiry
Applications
Interfaces
Diagnostics
Installation
FAQ
Recommend Models
Recommended Products

SIEMENS SIMATIC ET 200SP

6ES7132-6GD51-0BA0

RQ 4x24 VUC/2 A CO Standard relay output module

Exact Configuration

This ET 200SP Standard relay output module provides four floating changeover contacts for 24 V AC or DC resistive loads. Each channel has a common, normally closed and normally open contact.

Primary Function

Four isolated relay changeover outputs switch resistive field loads at up to 2 A per channel.

System Integration

Fits ET 200SP BaseUnit type A0 with CC00 identification and supports substitute values plus module diagnostics.

Technical Data

OFFICIAL CONFIGURATION DATA

6ES7132-6GD51-0BA0

Complete model	6ES7132-6GD51-0BA0
Product family	SIMATIC ET 200SP
Product type	RQ 4x24 VUC/2 A CO Standard relay output module
Hardware status	FS02 or later
Digital outputs	4 relay changeover contacts
Contact arrangement	Common, normally closed and normally open per channel
Rated supply voltage	24 V DC; permissible range 19.2 ... 28.8 V
Current consumption	50 mA rated
Power loss	Typically 1.2 W
Rated switching voltage	24 V DC or 24 V AC
Switching current	2 A maximum; 1 mA minimum at 5 V DC
Switching frequency	Maximum 2 Hz with resistive load
BaseUnit	Type A0
Color code	CC00
Diagnostics	Supply voltage and module diagnostics
Operating temperature	-30 ... +60 deg C horizontal; -30 ... +50 deg C vertical
Protection rating	IP20 within ET 200SP system
Dimensions	15 x 73 x 58 mm (W x H x D)
Weight	Approximately 30 g

Inquiry

CONTACT

STELLA

Email Inquiry [email protected]

WhatsApp +86 18159889985

Applications

DEPLOYMENT PROFILE

Relay-isolated field switching

Resistive loads

Switch four 24 V AC or DC resistive loads through floating changeover contacts.

Signal adaptation

Use relay isolation where transistor outputs are unsuitable for the connected field circuit.

Control behavior

Configure substitute values and reaction to CPU STOP in the ET 200SP project.

Interfaces

RELAY INTERFACES

Changeover-contact architecture

Four channels

Each output provides common, normally closed and normally open terminals.

Contact rating

Rated switching voltage is 24 V AC/DC with up to 2 A continuous current per channel.

Cable length

Official limits are 1000 m shielded or 200 m unshielded.

Diagnostics

DIAGNOSTICS

Module and supply monitoring

Supply diagnostics

The module can report missing or insufficient L+ supply voltage.

Visual status

DIAG, channel-status and PWR LEDs support commissioning and maintenance.

Fault scope

The module does not provide wire-break or short-circuit diagnostics at the relay contacts.

Installation

INSTALLATION

BaseUnit wiring and thermal limits

BaseUnit

Install on ET 200SP BaseUnit type A0 and use the CC00 identification code.

Contact wiring

Wire common, NC and NO terminals according to the required fail-state behavior and load circuit.

Thermal conditions

Observe -30 ... +60 deg C horizontal and -30 ... +50 deg C vertical operating limits.

FAQ

PROCUREMENT AND ENGINEERING CHECKS

Six model-specific questions

Q1. How can a buyer confirm the quoted unit is exactly 6ES7132-6GD51-0BA0?

A1. Match the complete Siemens article number, RQ 4x24 VUC/2 A CO ST designation, BaseUnit A0 and CC00 code on the label, packaging and quotation.

Q2. How can New, Used or Refurbished condition be distinguished?

A2. Request current photos of sealed packaging, nameplate, relay terminal area and BaseUnit connector, plus lot or serial data and written disclosure of prior switching use or repair.

Q3. How should the supplier be verified?

A3. Confirm the legal company, address, payment beneficiary and automation supply record. The written offer must identify 6ES7132-6GD51-0BA0 and the exact condition.

Q4. Which specifications should engineers check before purchase?

A4. Confirm four changeover contacts, 24 V AC/DC switching, 2 A rating, A0 BaseUnit, 15 x 73 x 58 mm dimensions, approximately 30 g weight and the required fail-state behavior.

Q5. What physical evidence should be requested before payment?

A5. Ask for time-stamped images of the actual module, article number, terminal markings, connector edge, packaging and shipment-specific identifiers.

Q6. Can a transistor output or another relay suffix replace it?

A6. Not automatically. Contact topology, current rating, diagnostics, switching frequency and project configuration differ; the electrical design and ET 200SP hardware project must approve any substitute.

Recommend Models

RECOMMEND MODEL
DS14	5X00226G04	1C31113G05
HFZ25	SPIIT13	PR6423/00R-010
SE4017P0	MVP50	IMDSM04
KJ3221X1-BA3	NPM22	5X00500G0
5X00500G01/1X00691H01	KJ3208X1-BA2	110E-JFS4J-912DA/NF2
V18345-302712000ZZ	KJ3243X1-BB1	KJ2005X1-BA2
SPDSI22	3051S2CD2A	3051TA1A
EJA530E-JBS	1C311	TPS02
EJA110E-JHS5J	IMMFP12	LR560
SPDSI13/SPFEC12/SPAS	RBC410	EJA438E-JAS
1C31219G01/1C31223G01	SE4603T05	HSS03
1C31122G02/1C31125G2	5X00063G01	KL4503X1-CA1
1C311166G02/1C31169G02	OC6000e	369B1848G5007
CE4001S2T2B6	SPASO11	BRC400
SE4001S2T2B5	CE4100	OC6000
5X00481G04/5X00226G04	IIT13	PR6423/10R-111
KJ4001X1-CC1	VE4031S2T2B6	KJ2201X1-JA1
KJ4110X1-BA1	SPBRC410ABB	KJ3208X1-BK1
5X00717G01	SPBRC410	KC4011X1-BP1
KJ4006X1-BK1	KJ3008X1-BA1	PR9268/201-000