Home > Products > EMERSON > EMERSON Delta V
|
Complete model
|
VE4035S2B1
|
|
Brand
|
Emerson
|
|
Product family
|
DeltaV M-series Traditional I/O
|
|
Product type
|
Redundant HART analog output I/O interface with standard termination block
|
|
Number of channels
|
8
|
|
Nominal signal range
|
4 to 20 mA
|
|
Full signal range
|
1 to 23 mA
|
|
Isolation
|
Each channel optically isolated from the system; factory tested to 1500 VDC
|
|
Accuracy over temperature
|
0.25% of span
|
|
Resolution
|
12-bit
|
|
Output compliance
|
20 mA at 21.6 VDC supply into 700 ohm load
|
|
LocalBus current
|
100 mA typical; 150 mA maximum per card at 12 VDC nominal
|
|
Field circuit power
|
300 mA maximum at 24 VDC, +/-10% per card
|
|
Calibration
|
Information stored on card
|
|
Redundancy behavior
|
Automatic active/standby recognition and switchover on a redundant terminal block
|
|
I/O card keying
|
A4
|
|
Termination
|
Redundant standard I/O termination block
|
|
Dimensions
|
H 10.7 x W 4.1 x D 10.5 cm
|
|
Weight
|
Not separately published for VE4035S2B1 in the selected official document
|
|
Protection rating
|
IP20
|
|
Operating temperature
|
-40 to 70 deg C
|
|
Storage temperature
|
-40 to 85 deg C
|
|
Relative humidity
|
5 to 95% non-condensing
|
|
Software note
|
Supported on DeltaV v10.3.1 and later; earlier versions use KJ3221X1-BA2
|
|
Certifications
|
CE, FM, CSA, ATEX, IECEx; marine certifications include IACS E10, ABS and DNV
|
|
Exact marking
|
VE4035S2B1
|
|
Official identity
|
redundant 8-channel 4-20 mA HART analog output I/O interface
|
|
Evidence to match
|
Match the complete VE4035S2B1 marking, redundant standard AO termination block, 8-channel 4-20 mA HART service and A4 keying.
|
|
System
Use with the matched 8-channel HART AO cards in a DeltaV M-series redundant I/O position. Verify DeltaV v10.3.1 or later, A4 keying, carrier and software revision.
|
Key selection
8 channels | 4-20 mA | HART | Redundant standard block | Key A4
|
Source control
Use the current official Emerson data sheet and confirm the installed carrier, software and revision before substitution.
|
|
Keying
Confirm both redundant card positions, A4 keying and 4-20 mA output loop loading. The controller identifies active and standby cards through the redundant terminal block.
|
Field wiring
Verify polarity, signal range, isolation and the exact terminal-block wiring before energizing.
|
Environment
Maintain the published -40 to 70 deg C operating range, IP20 protection and applicable hazardous-area procedures.
|
|
Identity
Require a clear current photo showing the complete VE4035S2B1 marking.
|
Engineering match
Require the full model label, redundant AO terminal-block identity, A4 keying, both card positions, connector condition and close-up terminal photos.
|
Condition evidence
Request label, housing, connector, terminal, keying, seal and packaging photos before payment.
|
|
Recommended Model
|
Recommended Model
|
Recommended Model
|
|---|---|---|
|
1756-IB32
|
KJ3002X1-BC1
|
TU831V1
|
|
KJ3202X1-BA1
|
KJ3001X1-BA1
|
VE4005S2B3
|
|
DI525
|
ARM55W
|
TU516
|
|
CC-TAIX01
|
TB511-ETH
|
CI853K01
|
|
6EP1332-1SH71
|
1756-L63
|
6ED1052-1FB08-0BA2
|
|
VE3051C0
|
1756-IA16
|
AAI141
|
|
AI523
|
1756-L83E
|
A2FV70S
|
|
CI873K01
|
6ES7288-2QR16-0AA0
|
6ES7153-4BA00-0XB0
|
|
AEA4D
|
6ES7223-1PL32-0XB0
|
CC-TDOB01
|
|
1756-A13
|
6ES7513-1RL00-0AB0
|
ADV869
|
|
6ES7518-4AP00-0AB0
|
DA501
|
CM578-CN
|
|
1756-L71
|
6ES7405-0DA02-0AA0
|
ASR133
|
|
1769-L18ERM-BB1B
|
DI810
|
6ES7288-1ST20-0AA1
|
|
VE4005S2B1
|
1756-PA72
|
1756-L81E
|
|
AI825
|
PM5112-R-ETH
|
6ES7288-2DT08-0AA0
|
|
DI811
|
CC-TCNT01
|
CI867K01
|
|
AI820
|
1756-A7
|
6ES7531-7PF00-0AB0
|
|
6ES7551-1AB00-0AB0
|
ATA4S
|
DO562
|
|
6ES7590-1AE80-0AA0
|
6ES7511-1CK01-0AB0
|
6ED1052-2FB08-0BA2
|
|
A2FV70D
|
5069-L330ERMS2
|
DI524
|
EN
