ALL PRODUCTS

Bently Nevada 7200 21747-075-00 7.5 m Unarmored Extension Cable | Original New

Bently Nevada 7200 21747-075-00 7.5 m Unarmored Extension Cable | Original New

BENTLY NEVADA · 7200

21747-075-00

Legacy 7200 5 mm and 8 mm proximity transducer extension cable, 7.5 m, without armor.

CONFIGURATION 7.5 m cable / no armor	INTERFACE 7200 5 mm and 8 mm
LEAD TIME In stock	WARRANTY 1 year

Email Inquiry [email protected]

WhatsApp +86 18159889985

Appurtenance:

bently nevada 7200 21747 075 00 7 5 m unarmored extension cable original new-1

Overview
Technical Data
Inquiry
Applications
Construction
Installation
Selection
FAQ
Recommend Models
Recommended Products

LEGACY 7200 PROXIMITY-TRANSDUCER EXTENSION CABLE

7200 5 mm and 8 mm

A legacy 7200 extension cable used between compatible 5 mm or 8 mm probes and the Proximitor in a correctly matched proximity-transducer system.

DOCUMENTED MODEL
21747-075-00

SYSTEM FAMILY
7200

PRIMARY VALUE
7.5 m cable / no armor

Technical Data

21747-075-00 Technical Data

Officially documented configuration and performance data.

Complete model	21747-075-00
Product family	Bently Nevada 7200 Transducer System
Product type	Legacy 7200 proximity-transducer extension cable
Dimensions	7.5 m cable length; cable outside diameter not separately specified in the manufacturer datasheet
Weight	Not separately specified; 0.59 kg is stated for the complete 7200 transducer system
System compatibility	7200 5 mm and 8 mm Proximity Transducer Systems
Order code length	075: 7.5 m extension cable
Armor option	00: without armor
System linear range	2.0 mm (80 mils), approximately 0.25 to 2.3 mm
System scale factor	7.87 V/mm (200 mV/mil)
System frequency response	0 to 10 kHz
Cable temperature	-34 to +177 deg C
Installation rule	Probe plus extension cable must equal the selected system length within the documented tolerance

Inquiry

CONTACT

STELLA

Email Inquiry [email protected]

WhatsApp +86 18159889985

Applications

Where this configuration fits and why it is selected.

Signal extension Connects a compatible 7200 probe to its Proximitor while preserving the calibrated electrical length.	Rotating machinery Supports shaft vibration and position loops on turbines, compressors, pumps and motors.
Legacy maintenance Provides a length-coded cable option for installed 7200 5 mm and 8 mm systems.	Field routing The unarmored construction suits protected routing where external mechanical armor is not required.

Construction

Documented materials, mechanical build and signal interfaces.

Cable assembly Coaxial extension-cable assembly for the legacy 7200 proximity-transducer family.	Length 7.5 m as defined by ordering code 075.
Protection Ordering code 00 specifies an unarmored cable.	Connections Mates only with the corresponding 7200 probe and Proximitor interfaces for the selected system family.

Installation

Mounting and Commissioning

A controlled sequence for installation and acceptance.

01 Identify the loop Confirm the installed probe and Proximitor belong to the 7200 5 mm or 8 mm family.	02 Verify electrical length Ensure probe plus extension cable equals the specified system length.
03 Protect the route Support the unarmored cable away from abrasion, hot surfaces, sharp bends and electrical interference.	04 Commission the system Check the static gap and dynamic response through the complete matched transducer loop.

Selection

Ordering Code Decoded

Each suffix identifies a physical, electrical or approval choice.

21747	7200 5 mm and 8 mm extension cable
075	Cable length: 7.5 m
00	Without protective armor
System rule	Probe and extension cable form the required total electrical length
Compatibility	Use only with the corresponding 7200 probe and Proximitor family

FAQ

BUYER AND ENGINEER CHECKLIST

Six model-specific checks for sourcing and technical acceptance.

Q1. How can a buyer verify the exact quoted model?

Require 21747-075-00 on the quotation and cable identification. It defines a 7.5 m 7200 extension cable without armor.

Q2. How can New, Used and Refurbished condition be distinguished?

Request dated photos of the full coiled cable, both connectors and all labels. Inspect for cuts, crushed sections, reterminated ends, oxidation or mismatched identification sleeves.

Q3. How should an industrial buyer qualify the supplier?

Verify the legal entity, payment beneficiary and traceability, and require current evidence of the exact 7.5 m unarmored cable rather than a generic 7200 cable image.

Q4. What must engineering confirm before purchase?

Confirm the installed 7200 5 mm or 8 mm family, probe length, required total system length, connector compatibility, cable route and whether armor is required.

Q5. What evidence should be requested before payment?

Ask for current full-length and label photos, connector close-ups, measured cable length, packaging evidence and any agreed continuity or insulation test record.

Q6. Can another length or armored suffix be substituted?

Not without recalculating the complete system. Cable length affects electrical calibration, and an armor suffix changes routing and mechanical protection.

Recommend Models

Recommend Model

EL1014	SHO100-T	ASD07N4
QBGF1020V	NP3X-D	JL325-61001
SLA12-LAS-T/24	M3000	mdm021
SYS-7850	ST-CE1075-2-U100-B	130B1169
330-C1	KJ1502X1-BD1	TST8804
PCB00259-02	FS-Router-BAC2	XBTGT5330
203LS-D	371-099	PS236
3TX7116-5FC13C	RM-PS-024-01F	XB15
227575-PR	033010-A	STR2003DA
DRC820F	EC-7850-A-1072	R26P
ANFGW-422A	ED100-LA-000-000	DI6S
IJ-PR-95-265	SB401-50	T9100
AG8/WB	CWSS-RB-W7	BT-F420
RS-481	NC3MD-LX	RS900-HI-D-C2-C2-00
170PNT11020	3-2485	S-3-TCPUSE-H-Di6
INT-1534-M-5-M-111	3HE11904AARB01	MTN649204
MB4S-E	RDF60.1	IOM3721
HT22	Bmxxbp0800	DPB07S15
SMB-00920-4	PT220-256L-DNET	UX1K-AMN-4FXS
SB-RLY12C10A-DN	IGT-905A	167A.000367