Home > Products > SIEMENS > SIMATIC S7 Series
|
Complete model
|
6ES7532-5HD00-0AB0
|
|
Product family
|
SIMATIC S7-1500 SM 532 analog output modules
|
|
Product type
|
AQ 4xU/I ST analog output module
|
|
HW functional status
|
From FS04
|
|
Firmware version
|
V2.2.0; firmware update possible
|
|
Supply voltage
|
24 V DC; permissible range 20.4 to 28.8 V
|
|
Current consumption
|
190 mA maximum at 24 V DC
|
|
Power loss
|
4 W typical
|
|
Analog outputs
|
4 channels in one group of 4
|
|
Voltage ranges
|
0 to 10 V; 1 to 5 V; -10 to +10 V
|
|
Current ranges
|
0 to 20 mA; -20 to +20 mA; 4 to 20 mA
|
|
Resolution
|
16 bit including overrange and sign
|
|
Cycle time
|
3.2 ms minimum for all channels
|
|
Conversion time
|
0.5 ms per channel
|
|
Load limits
|
Voltage at least 1 kOhm; current up to 750 Ohm
|
|
Cable length
|
Shielded: up to 800 m for current and 200 m for voltage
|
|
Accuracy
|
Operational error limit plus or minus 0.3% for voltage or current
|
|
Diagnostics
|
Supply monitoring, current-output wire break, voltage-output short circuit, overflow and underflow
|
|
Isolation
|
707 V DC type test; channels isolated from backplane bus and load voltage
|
|
Operating temperature
|
-30 to 60 deg C horizontal from FS06; -30 to 40 deg C vertical
|
|
Installation altitude
|
Up to 5,000 m with restrictions above 2,000 m
|
|
Dimensions
|
35 x 147 x 129 mm (W x H x D)
|
|
Weight
|
Approximately 310 g
|
|
Engineering
|
TIA Portal V12; STEP 7 V5.5 SP3; PROFINET GSD V2.3
|
|
Safety support
|
Safety-oriented load-group shutdown up to SIL2 and Category 2 / PL c
|
|
Analog generation
Four channels generate voltage or current signals with 16-bit resolution and a 0.5 ms conversion time per channel.
|
Output timing
The minimum cycle time for all active channels is 3.2 ms, independent of channel count.
|
|
Substitute values
Substitute output values can be configured for controlled behavior during faults or controller transitions.
|
Safety-oriented shutdown
The module supports shutdown of load groups up to SIL2 and Category 2 / PL c when applied as specified.
|
|
Voltage outputs
Available ranges are 0 to 10 V, 1 to 5 V, and -10 to +10 V with short-circuit protection.
|
Current outputs
Available ranges are 0 to 20 mA, -20 to +20 mA, and 4 to 20 mA.
|
|
Actuator wiring
Two-wire voltage, four-wire voltage, and two-wire current actuator connections are supported.
|
Field connection
An infeed element, shielding bracket, and shield terminal are included; the front connector is ordered separately.
|
|
Supply diagnostics
The 24 V DC supply is monitored and indicated by the green PWR LED.
|
Channel diagnostics
Current-mode wire break, voltage-mode short circuit, overflow, and underflow can be diagnosed.
|
|
Status indicators
RUN, ERROR, PWR, channel status, channel diagnostic, and module diagnostic indications are provided.
|
Diagnostic alarm
The module can issue diagnostic alarms and apply configured substitute values.
|
|
Module dimensions
The module measures 35 x 147 x 129 mm and weighs approximately 310 g.
|
Front connector
Use the separately ordered screw-terminal or push-in front connector with the supplied shielding components.
|
|
Ambient orientation
Horizontal operation is specified to 60 deg C and vertical operation to 40 deg C from FS06.
|
Engineering requirement
Configure using TIA Portal V12, STEP 7 V5.5 SP3, or the applicable PROFIBUS or PROFINET GSD.
|
|
Q1. How can I verify that the quoted item is exactly 6ES7532-5HD00-0AB0?
Match the complete order number on the module label, quotation, packaging, and invoice. Confirm AQ 4xU/I ST, four channels, 16-bit resolution, FS04 or later, and the 35 mm module width.
|
|
Q2. How can I distinguish a new AQ 4xU/I ST module from a used or refurbished unit?
Request current photos of the Siemens label, front-connector socket, backplane contacts, shielding parts, rail latch, LEDs, and packaging. Check for terminal wear, scratches, bent contacts, relabeling, or resealing.
|
|
Q3. How should a buyer verify that the supplier is legitimate and reliable?
Verify the legal company name, registration, business address, bank beneficiary, and S7-1500 supply references. All commercial records must consistently identify 6ES7532-5HD00-0AB0.
|
|
Q4. Which specifications should an engineer verify before purchasing?
Confirm four voltage or current outputs, required signal ranges, 16-bit resolution, 24 V DC supply, front-connector choice, 35 x 147 x 129 mm dimensions, and approximately 310 g weight.
|
|
Q5. What physical evidence should be requested before payment?
Request timestamped photos or video of the full order-number label, channel markings, connector socket, backplane contacts, supplied shielding parts, housing condition, and sealed Siemens packaging.
|
|
Q6. Can another SM 532 suffix replace 6ES7532-5HD00-0AB0?
Not automatically. Similar modules can change channel count, signal ranges, resolution, accuracy, diagnostic coverage, cycle time, safety shutdown support, or connector requirements. Engineering must verify the exact output design.
|
|
19D902780G6
|
ADAM-4051
|
ABB CPU PM582 1SAP140200R0201
|
|
PD2-M-2C-12-48V-RR-92305
|
KJ2003X1-BA2 /12P2093X102
|
XEV01D XEV01D-5N0B0-001
|
|
ABB 1SD A066324
|
AI88-1A
|
033010-A
|
|
XFR822A XS821-22
|
0J-0P4595AB
|
DIU211 2071670A
|
|
CP3N
|
TCC241 100/1A 50-60HZ P01379601
|
AWK-3121-US-T
|
|
ADLY-4
|
EZC100N3015 EZC100N
|
6ES7134-6HD00-0BA1
|
|
GE IC3600SSLB1H1B 006/03
|
PZ16 9012600000
|
GHG5117306R0001
|
|
EPACK-1PH
|
URX-P2
|
SEM203P / PT100 363-0238
|
|
ABB 8.230.1M GH Q631 0078 R0111
|
AMB-P3-CN
|
CS-AMS8 RS485
|
|
CN35BN3AB
|
CDH4U5-BDALI
|
KPD-4400
|
|
GE NMTCV2
|
HPBYB8A 316SS-PTFE
|
ABB YO-1SDA038291R1 YC-1SDA038301R1
|
|
MILLENIUM3 CD12
|
CLEA2026B31
|
C441BA
|
|
1125WBN-10PKG
|
ABB 1MRK000614-ABR09 / 93-1001-04
|
10D14
|
|
335/400 FLHTF400A230
|
M2PBMPP
|
AKB331-M020
|
|
8827790000
|
D950EF-00
|
110100501
|
|
7KG6101-2EH10
|
TM3DI32K
|
1957/00 890019570001
|
|
DLS/3PH-BUS
|
KFD2-SCD2-EX1.LK
|
130054 R 1805
|
|
RIL230A N1103ME
|
33729-03
|
C2IR-8 6500429
|
|
BRESSER 47-01180
|
2010105S811
|
9000-41034-0401005
|
|
CLR96 946040
|
S2F-01001/L
|
TC908A1000
|
EN
