Two-axis High Standard control unit for SIMODRIVE 611 digital drive systems
The 6SN1118-0DM31-0AA2 is a two-axis High Standard closed-loop control module for SIMODRIVE 611 with digital setpoint interface, sin/cos 1 Vpp encoder feedback and NC software integration. Correct replacement depends on the power module, motor and encoder interfaces, SINUMERIK drive software and commissioning archive.
Drive-system match: Confirm the full control-unit label, two-axis High Standard version, 1 Vpp encoder type and connector assignment, installed SIMODRIVE power module, SINUMERIK NCU and drive software release, motor data, measuring systems and safety and brake wiring before ordering.
Drive Matching
6SN1118-0DM31-0AA2 is a SIMODRIVE 611 digital High Standard control unit for two axes. During initialization, its drive software is supplied through the SINUMERIK 840D drive bus, so the control board cannot be assessed independently from the NCU software and machine commissioning data.
Un intercambiu controlatu incipit cun un archivu NC integru e un archivu de comandu, plus un mapu de cunnettoris pro utrius axes. Registrae li motores e li enkodores de mesura diretta, li sircurus de abilitatzione e de inibitzione de partenza, li contrullus de frene, li istados de DAC e diagnostica, tunc comparare li cumportamentu novu de cada asse antès de permitere su movimentu.
L’identidade de sa scheda, su software e s’hardware de s’asse deben èssere revistos comente un sistema unicu de comandu.
Software archive
Preservare l’archivu de messa in servitziu NC e de comandu, li versiones de software NCU e de comandu, e l’assignatzione de s’asse.
Potentzia e motore
Registrae su mòdulu de potentzia SIMODRIVE, su tipu de motore, li datos nominàlis, su frene e ambas li cunnettionis de enkodor de motore.
Sistemas de mesura
Mappare X411, X412, X421 e X422 e cunfirmare su segnale de 1 Vpp o EnDat atzetadu pro cada asse.
Wiring & Encoder
Sa positzione de su cunnettori a su solu non bastat; documentare funtzione, asse e tipu de segnale.
Catena de abilitatzione
Registrae su feedback de inibitzione de partenza, l’abilitatzione de impulsi, l’abilitatzione de comandu e sa lochica de sigurèntzia esterna antès de disconnettere.
Circulus frenorum
Verificare suppetitiam frenorum 24 V approbatam, interfaciem rellais, suppressionem et attributionem axium.
Examen motus regulati
Post restitutum parametrum, probare directionem retroactionis, velocitatem nullam, liberationem frenorum et motum limitatum unum axem per tempus.
Specificationes
Designatio generis producti
Unitas controlis digitalis SIMODRIVE 611 High Standard
Numerus ordinis
6SN1118-0DM31-0AA2
Axis capacity
2 axes
Interfacies Puncti Praefiniti
Interficies digitalis ducens-motus
Ingressus encoderis motoris
Sin/cos 1 Vpp
Ingressus mensurae directae
Interficies bi-axialis, dependens ab applicatione
Integratio Controlli
Systema SINUMERIK 840D / SIMODRIVE 611
Software loading
Downloaded from the NCU during initialization
Key connectors
X411/X412 motor encoder; X421/X422 direct measurement
Safety and enable interface
Start inhibit, pulse enable and drive enable circuits
How can I confirm that 6SN1118-0DM31-0AA2 is compatible with the installed SIMODRIVE 611 system?
Match the complete two-axis High Standard order number, SIMODRIVE power module, SINUMERIK NCU and drive software release. Confirm motor types, sin/cos 1 Vpp or EnDat feedback, direct measuring systems and all enable and brake interfaces for both axes.
Q2
Quid servari debet antequam 6SN1118-0DM31-0AA2 substituitur?
Create a complete NC and drive commissioning archive and record NCU, drive and firmware versions. Photograph every connector and label both axes, motor encoders, direct measuring systems, enables, start-inhibit feedback, brakes and DAC test points before power is isolated.
Q3
Why can 6SN1118-0DM31-0AA2 remain inactive after the commissioning archive is restored?
Check that the NCU downloads the expected drive software, then review start-inhibit feedback, pulse and drive enables and the drive-bus connection. Compare the control-unit and axis assignments with the archived machine data before changing parameters.
Q4
What should I inspect when one axis on 6SN1118-0DM31-0AA2 reports an encoder fault?
Verify that the affected motor encoder is connected to the correct X411 or X412 interface and that signal type and supply match the configured motor. Inspect shield continuity, connector pins and cable condition, then compare live feedback with the stationary-axis expectation.
Q5
Quomodo frenum motoris post installationem 6SN1118-0DM31-0AA2 examinandum est?
Machinam in statu tuti et regulato retinere, et supplitium externum freni 24 V, attributionem rellais et circuitum suppressionis verificare. Freni liberationem et retentionem cum torque et cursu limitatis experiri; directionem feedback confirmare et responsionem pro singulis axibus ante motum normalem documentare.
Q6
Cur aequatio visualis ad 6SN1118-0DM31-0AA2 quaerendum insufficiens est?
Unitates de control SIMODRIVE 611, quae similem frontem habent, inter se differre possunt secundum numerum axium, controllem High Standard vel High Performance, interfaciem encoderis et integrationem software. Ad approbandum reservatum, totum numerum ordinis et archivum machinae installatae uti oportet, non solum aspectum connectoris.
EN
